nxp.com LPC82x 1.0 LPC822M101JDH20,LPC822M101JHI33,LPC824M201JDH20,LPC824M201JHI33 Copyright 2016-2019 NXP All rights reserved. SPDX-License-Identifier: BSD-3-Clause CM0PLUS r0p1 little false false true 2 false 8 32 MTB_SFR LPC82x Micro Trace Buffer MTB 0x14000000 0 0x10 registers POSITION POSITION Register 0 32 read-write 0 0 WRAP This bit is set to 1 automatically when the POINTER value wraps as determined by the MASTER.MASK field in the MASTER Trace Control Register. 2 1 read-write POINTER Trace packet location pointer. Because a packet consists of two words, the POINTER field is the location of the first word of a packet. This field contains bits [31:3] of the address, in the SRAM, where the next trace packet will be written. The field points to an unused location and is automatically incremented. A debug agent can calculate the system address, on the AHB-Lite bus, of the SRAM location pointed to by the POSITION register using the following equation: system address = BASE + ((P + (2AWIDTH - (BASE MOD 2AWIDTH))) MOD 2AWIDTH). Where P = POSITION AND 0xFFFF_FFF8. Where BASE is the BASE register value 3 29 read-write MASTER MASTER Register 0x4 32 read-write 0x80 0x800003E0 MASK This value determines the maximum size of the trace buffer in SRAM. It specifies the most-significant bit of the POSITION.POINTER field that can be updated by automatic increment. If the trace tries to advance past this power of two, the POSITION.WRAP bit is set to 1, the POSITION.POINTER[MASK:0] bits are set to zero, and the POSITION.POINTER[AWIDTH-4:MASK+1] bits remain unchanged. This field causes the trace packet information to be stored in a circular buffer of size 2(MASK+4) bytes, that can be positioned in memory at multiples of this size. Valid values of this field are zero to AWIDTH-4. Values greater than the maximum have the same effect as the maximum. 0 5 read-write TSTARTEN Trace start input enable. If this bit is 1 and the TSTART signal is HIGH, then the EN bit is set to 1. Tracing continues until a stop condition occurs. 5 1 read-write TSTOPEN Trace stop input enable. If this bit is 1 and the TSTOP signal is HIGH, then the EN bit is set to 0. If a trace packet is being written to memory, the write is completed before tracing is stopped. 6 1 read-write SFRWPRIV Special Function Register Write Privilege bit. If this bit is 0, then User or Privileged AHB-Lite read and write accesses to the Special Function Registers are permitted. If this bit is 1, then only Privileged write accesses are permitted and User write accesses are ignored. The HPROT[1] signal determines if an access is User or Privileged. 7 1 read-write RAMPRIV SRAM Privilege bit. If this bit is 0, then User or Privileged AHB-Lite read and write accesses to the SRAM are permitted. If this bit is 1, then only Privileged AHB-Lite read and write accesses to the SRAM are permitted and User accesses are RAZ/WI. The HPROT[1] signal determines if an access is User or Privileged. 8 1 read-write HALTREQ Halt request bit. This bit is connected to the halt request signal of the trace logic, EDBGRQ. When HALTREQ is set to 1, EDBGRQ is asserted if DBGEN is also HIGH. The HALTREQ bit can be automatically set to 1 using the FLOW.WATERMARK field. 9 1 read-write EN Main trace enable bit. When this bit is 1 trace data is written into the SRAM memory location addressed by POSITION.POINTER. The POSITION.POINTER value auto increments after the trace data packet is written. The EN bit can be automatically set to 0 using the FLOW.WATERMARK field and the FLOW.AUTOSTOP bit. The EN bit is automatically set to 1 if the TSTARTEN bit is 1 and the TSTART signal is HIGH. The EN bit is automatically set to 0 if TSTOPEN bit is 1 and the TSTOP signal is HIGH. 31 1 read-write FLOW FLOW Register 0x8 32 read-write 0 0x3 AUTOSTOP If this bit is 1 and WATERMARK is equal to POSITION.POINTER, then the MASTER.EN bit is automatically set to 0. This stops tracing. 0 1 read-write AUTOHALT If this bit is 1 and WATERMARK is equal to POSITION.POINTER, then the MASTER.HALTREQ bit is automatically set to 1. If the DBGEN signal is HIGH, the MTB asserts this halt request to the Cortex-M0+ processor by asserting the EDBGRQ signal. 1 1 read-write WATERMARK WATERMARK value. This field contains an address in the same format as the POSITION.POINTER field. When the POSITION.POINTER matches the WATERMARK field value, actions defined by the AUTOHALT and AUTOSTOP bits are performed. 3 29 read-write BASE Indicates where the SRAM is located in the processor memory map. This register is provided to enable auto discovery of the MTB SRAM location, by a debug agent. 0xC 32 read-only 0 0 BASE The value provided is the value of the SRAMBASEADDR[31:0] signal. 0 32 read-only WWDT LPC82x Windowed Watchdog Timer (WWDT) WWDT 0x40000000 0 0x1C registers WDT 12 MOD Watchdog mode register. This register contains the basic mode and status of the Watchdog Timer. 0 32 read-write 0 0x3F WDEN Watchdog enable bit. Once this bit is set to one and a watchdog feed is performed, the watchdog timer will run permanently. 0 1 read-write STOP Stop. The watchdog timer is stopped. 0 RUN Run. The watchdog timer is running. 0x1 WDRESET Watchdog reset enable bit. Once this bit has been written with a 1 it cannot be re-written with a 0. 1 1 read-write INTERRUPT Interrupt. A watchdog time-out will not cause a chip reset. 0 RESET Reset. A watchdog time-out will cause a chip reset. 0x1 WDTOF Watchdog time-out flag. Set when the watchdog timer times out, by a feed error, or by events associated with WDPROTECT. Cleared by software writing a 0 to this bit position. Causes a chip reset if WDRESET = 1. 2 1 read-write WDINT Warning interrupt flag. Set when the timer is at or below the value in WDWARNINT. Cleared by software writing a 1 to this bit position. Note that this bit cannot be cleared while the WARNINT value is equal to the value of the TV register. This can occur if the value of WARNINT is 0 and the WDRESET bit is 0 when TV decrements to 0. 3 1 read-write WDPROTECT Watchdog update mode. This bit can be set once by software and is only cleared by a reset. 4 1 read-write FLEXIBLE Flexible. The watchdog time-out value (TC) can be changed at any time. 0 THRESHOLD Threshold. The watchdog time-out value (TC) can be changed only after the counter is below the value of WDWARNINT and WDWINDOW. 0x1 LOCK Once this bit is set to one and a watchdog feed is performed, disabling or powering down the watchdog oscillator is prevented by hardware. This bit can be set once by software and is only cleared by any reset. 5 1 read-write TC Watchdog timer constant register. This 24-bit register determines the time-out value. 0x4 32 read-write 0xFF 0xFFFFFF COUNT Watchdog time-out value. 0 24 read-write FEED Watchdog feed sequence register. Writing 0xAA followed by 0x55 to this register reloads the Watchdog timer with the value contained in TC. 0x8 32 write-only 0 0 FEED Feed value should be 0xAA followed by 0x55. 0 8 write-only TV Watchdog timer value register. This 24-bit register reads out the current value of the Watchdog timer. 0xC 32 read-only 0xFF 0xFFFFFF COUNT Counter timer value. 0 24 read-only WARNINT Watchdog Warning Interrupt compare value. 0x14 32 read-write 0 0x3FF WARNINT Watchdog warning interrupt compare value. 0 10 read-write WINDOW Watchdog Window compare value. 0x18 32 read-write 0xFFFFFF 0xFFFFFF WINDOW Watchdog window value. 0 24 read-write MRT0 LPC82x Multi-Rate Timer (MRT) MRT 0x40004000 0 0xFC registers MRT0 10 4 0x10 CHANNEL[%s] no description available 0 INTVAL MRT Time interval value register. This value is loaded into the TIMER register. 0 32 read-write 0 0xFFFFFFFF IVALUE Time interval load value. This value is loaded into the TIMERn register and the MRT channel n starts counting down from IVALUE -1. If the timer is idle, writing a non-zero value to this bit field starts the timer immediately. If the timer is running, writing a zero to this bit field does the following: If LOAD = 1, the timer stops immediately. If LOAD = 0, the timer stops at the end of the time interval. 0 31 read-write LOAD Determines how the timer interval value IVALUE -1 is loaded into the TIMERn register. This bit is write-only. Reading this bit always returns 0. 31 1 read-write NO_FORCE_LOAD No force load. The load from the INTVALn register to the TIMERn register is processed at the end of the time interval if the repeat mode is selected. 0 FORCE_LOAD Force load. The INTVALn interval value IVALUE -1 is immediately loaded into the TIMERn register while TIMERn is running. 0x1 TIMER MRT Timer register. This register reads the value of the down-counter. 0x4 32 read-only 0xFFFFFF 0x7FFFFFFF VALUE Holds the current timer value of the down-counter. The initial value of the TIMERn register is loaded as IVALUE - 1 from the INTVALn register either at the end of the time interval or immediately in the following cases: INTVALn register is updated in the idle state. INTVALn register is updated with LOAD = 1. When the timer is in idle state, reading this bit fields returns -1 (0x00FF FFFF). 0 31 read-only CTRL MRT Control register. This register controls the MRT modes. 0x8 32 read-write 0 0x7 INTEN Enable the TIMERn interrupt. 0 1 read-write DISABLED Disabled. TIMERn interrupt is disabled. 0 ENABLED Enabled. TIMERn interrupt is enabled. 0x1 MODE Selects timer mode. 1 2 read-write REPEAT_INTERRUPT_MODE Repeat interrupt mode. 0 ONE_SHOT_INTERRUPT_MODE One-shot interrupt mode. 0x1 ONE_SHOT_STALL_MODE One-shot stall mode. 0x2 STAT MRT Status register. 0xC 32 read-write 0 0x3 INTFLAG Monitors the interrupt flag. 0 1 read-write NO_PENDING_INTERRUPT No pending interrupt. Writing a zero is equivalent to no operation. 0 PENDING_INTERRUPT Pending interrupt. The interrupt is pending because TIMERn has reached the end of the time interval. If the INTEN bit in the CONTROLn is also set to 1, the interrupt for timer channel n and the global interrupt are raised. Writing a 1 to this bit clears the interrupt request. 0x1 RUN Indicates the state of TIMERn. This bit is read-only. 1 1 read-write IDLE_STATE Idle state. TIMERn is stopped. 0 RUNNING Running. TIMERn is running. 0x1 MODCFG Module Configuration register. This register provides information about this particular MRT instance. 0xF0 32 read-write 0x1F4 0x1FF NOC Identifies the number of channels in this MRT.(4 channels on this device.) 0 4 read-only NOB Identifies the number of timer bits in this MRT. (31 bits wide on this device.) 4 5 read-only IDLE_CH Idle channel register. This register returns the number of the first idle channel. 0xF4 32 read-only 0 0xF0 CHAN Idle channel. Reading the CHAN bits, returns the lowest idle timer channel. The number is positioned such that it can be used as an offset from the MRT base address in order to access the registers for the allocated channel. If all timer channels are running, CHAN = 0xF. See text above for more details. 4 4 read-only IRQ_FLAG Global interrupt flag register 0xF8 32 read-write 0 0xF GFLAG0 Monitors the interrupt flag of TIMER0. 0 1 read-write NO_PENDING_INTERRUPT No pending interrupt. Writing a zero is equivalent to no operation. 0 PENDING_INTERRUPT Pending interrupt. The interrupt is pending because TIMER0 has reached the end of the time interval. If the INTEN bit in the CONTROL0 register is also set to 1, the interrupt for timer channel 0 and the global interrupt are raised. Writing a 1 to this bit clears the interrupt request. 0x1 GFLAG1 Monitors the interrupt flag of TIMER1. See description of channel 0. 1 1 read-write GFLAG2 Monitors the interrupt flag of TIMER2. See description of channel 0. 2 1 read-write GFLAG3 Monitors the interrupt flag of TIMER3. See description of channel 0. 3 1 read-write WKT LPC82x Wake Up Timer(WKT) WKT 0x40008000 0 0x10 registers WKT 15 CTRL Self wake-up timer control register. 0 32 read-write 0 0xF CLKSEL Select the self wake-up timer clock source. Remark: This bit only has an effect if the SEL_EXTCLK bit is not set. 0 1 read-write DIVIDED_IRC_CLOCK Divided IRC clock. This clock runs at 750 kHz and provides time-out periods of up to approximately 95 minutes in 1.33 us increments. Remark: This clock is not available in not available in Deep-sleep, power-down, deep power-down modes. Do not select this option if the timer is to be used to wake up from one of these modes. 0 LOW_POWER_CLOCK This is the (nominally) 10 kHz clock and provides time-out periods of up to approximately 119 hours in 100 us increments. The accuracy of this clock is limited to +/- 40 % over temperature and processing. Remark: This clock is available in all power modes. Prior to use, the low-power oscillator must be enabled. The oscillator must also be set to remain active in Deep power-down if needed. 0x1 ALARMFLAG Wake-up or alarm timer flag. 1 1 read-write NO_TIME_OUT No time-out. The self wake-up timer has not timed out. Writing a 0 to has no effect. 0 TIME_OUT Time-out. The self wake-up timer has timed out. This flag generates an interrupt request which can wake up the part from any reduced power mode including Deep power-down if the clock source is the low power oscillator. Writing a 1 clears this status bit. 0x1 CLEARCTR Clears the self wake-up timer. 2 1 read-write NO_EFFECT No effect. Reading this bit always returns 0. 0 CLEAR_THE_COUNTER Clear the counter. Counting is halted until a new count value is loaded. 0x1 SEL_EXTCLK Select external or internal clock source for the self wake-up timer. The internal clock source is selected by the CLKSEL bit in this register if SET_EXTCLK is set to internal. 3 1 read-write INTERNAL Internal. The clock source is the internal clock selected by the CLKSEL bit. 0 EXTERNAL External. The self wake-up timer uses the external WKTCLKIN pin. 0x1 COUNT Counter register. 0xC 32 read-write 0 0 VALUE A write to this register pre-loads start count value into the timer and starts the count-down sequence. A read reflects the current value of the timer. 0 32 read-write SWM0 LPC82x SWM SWM 0x4000C000 0 0x1C4 registers PINASSIGN0 Pin assign register 0. Assign movable functions U0_TXD, U0_RXD, U0_RTS, U0_CTS. 0 32 read-write 0xFFFFFFFF 0xFFFFFFFF U0_TXD_O U0_TXD function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 0 8 read-write U0_RXD_I U0_RXD function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 8 8 read-write U0_RTS_O U0_RTS function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 16 8 read-write U0_CTS_I U0_CTS function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN1 Pin assign register 1. Assign movable functions U0_SCLK, U1_TXD, U1_RXD, U1_RTS. 0x4 32 read-write 0xFFFFFFFF 0xFFFFFFFF U0_SCLK_IO U0_SCLK function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write U1_TXD_O U1_TXD function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write U1_RXD_I U1_RXD function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 16 8 read-write U1_RTS_O U1_RTS function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN2 Pin assign register 2. Assign movable functions U1_CTS, U1_SCLK, U2_TXD, U2_RXD. 0x8 32 read-write 0xFFFFFFFF 0xFFFFFFFF U1_CTS_I U1_CTS function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 0 8 read-write U1_SCLK_IO U1_SCLK function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 8 8 read-write U2_TXD_O U2_TXD function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 16 8 read-write U2_RXD_I U2_RXD function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN3 Pin assign register 3. Assign movable function U2_RTS, U2_CTS, U2_SCLK, SPI0_SCK. 0xC 32 read-write 0xFFFFFFFF 0xFFFFFFFF U2_RTS_O U2_RTS function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 0 8 read-write U2_CTS_I U2_CTS function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 8 8 read-write U2_SCLK_IO U2_SCLK function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0(= 0) to PIO0_28 (= 0x1C). 16 8 read-write SPI0_SCK_IO SPI0_SCK function assignment. The value is the pin number to be assigned to this function. The following pins are available:PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN4 Pin assign register 4. Assign movable functions SPI0_MOSI, SPI0_MISO, SPI0_SSEL0, SPI0_SSEL1. 0x10 32 read-write 0xFFFFFFFF 0xFFFFFFFF SPI0_MOSI_IO SPI0_MOSI function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write SPI0_MISO_IO SPI0_MISIO function assignment. The value is the pin number to be assigned to this function. The following pins are available:PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write SPI0_SSEL0_IO SPI0_SSEL0 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 16 8 read-write SPI0_SSEL1_IO SPI0_SSEL1 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN5 Pin assign register 5. Assign movable functions SPI0_SSEL2, SPI0_SSEL3, SPI1_SCK, SPI1_MOSI 0x14 32 read-write 0xFFFFFFFF 0xFFFFFFFF SPI0_SSEL2_IO SPI0_SSEL2 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write SPI0_SSEL3_IO SPI0_SSEL3 function assignment. The value is the pin number to be assigned to this function. The following pins are available:PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write SPI1_SCK_IO SPI1_SCK function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 16 8 read-write SPI1_MOSI_IO SPI1_MOSI function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN6 Pin assign register 6. Assign movable functions SPI1_MISO, SPI1_SSEL0, SPI1_SSEL1, SCT0_IN0. 0x18 32 read-write 0xFFFFFFFF 0xFFFFFFFF SPI1_MISO_IO SPI1_MISO function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write SPI1_SSEL0_IO SPI1_SSEL0 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write SPI1_SSEL1_IO SPI1_SSEL1 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 16 8 read-write SCT_PIN0_I SCT_PIN0 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN7 Pin assign register 7. Assign movable functions SCT_IN1, SCT_IN2, SCT_IN3, SCT_OUT0. 0x1C 32 read-write 0xFFFFFFFF 0xFFFFFFFF SCT_PIN1_I SCT_PIN1 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write SCT_PIN2_I SCT_PIN2 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write SCT_PIN3_I SCT_PIN3 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 16 8 read-write SCT_OUT0_O SCT_OUT0 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN8 Pin assign register 8. Assign movable functions SCT_OUT1, SCT_OUT2, SCT_OUT3, SCT_OUT4. 0x20 32 read-write 0xFFFFFFFF 0xFFFFFFFF SCT_OUT1_O SCT_OUT1 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write SCT_OUT2_O SCT_OUT2 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write SCT_OUT3_O SCT_OUT3 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 16 8 read-write SCT_OUT4_O SCT_OUT4 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN9 Pin assign register 9. Assign movable functions SCT_OUT5, I2C1_SDA, I2C1_SCL, I2C2_SDA. 0x24 32 read-write 0xFFFFFFFF 0xFFFFFFFF SCT_OUT5_O SCT_OUT5 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write I2C1_SDA_IO I2C1_SDA function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write I2C1_SCL_IO I2C1_SCL function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 16 8 read-write I2C2_SDA_IO I2C1_SDA function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN10 Pin assign register 10. Assign movable functions, I2C2_SCL, I2C3_SDA, I2C3_SCL, ADC_PINTRIG0. 0x28 32 read-write 0xFFFFFFFF 0xFFFFFFFF I2C2_SCL_IO I2C1_SCL function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write I2C3_SDA_IO I2C3_SDA function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write I2C3_SCL_IO I2C3_SCL function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 16 8 read-write ADC_PINTRIG0_I ADC_PINTRIG0 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINASSIGN11 Pin assign register 11. Assign movable functions ADC_PINTRIG1, ACMP_O, CLKOUT, GPIO_INT_BMAT 0x2C 32 read-write 0xFFFFFFFF 0xFFFFFFFF ADC_PINTRIG1_I ADC_PINTRIG1 function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 0 8 read-write ACMP_O_O ACMP_O function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 8 8 read-write CLKOUT_O CLKOUT function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 16 8 read-write GPIO_INT_BMAT_O GPIO_INT_BMAT function assignment. The value is the pin number to be assigned to this function. The following pins are available: PIO0_0 (= 0) to PIO0_28 (= 0x1C). 24 8 read-write PINENABLE0 Pin enable register 0. Enables fixed-pin functions ACMP_I0, ACMP_I1, SWCLK, SWDIO, XTALIN, XTALOUT, RESET, CLKIN, VDDCMP and so on. 0x1C0 32 read-write 0xFFFFFECF 0xFFFFFFFF ACMP_I1 ACMP_I1 function select. 0 1 read-write ENABLED ACMP_I1 enabled on pin PIO0_00. 0 DISABLED ACMP_I1 disabled. 0x1 ACMP_I2 ACMP_I2 function select. 1 1 read-write ENABLED ACMP_I2 enabled on pin PIO0_1. 0 DISABLED ACMP_I2 disabled. 0x1 ACMP_I3 ACMP_I3 function select. 2 1 read-write ENABLED ACMP_I3 enabled on pin PIO0_14. 0 DISABLED ACMP_I3 disabled. 0x1 ACMP_I4 ACMP_I4 function select. 3 1 read-write ENABLED ACMP_I4 enabled on pin PIO0_23. 0 DISABLED ACMP_I4 disabled. 0x1 SWCLK SWCLK function select. 4 1 read-write ENABLED SWCLK enabled on pin PIO0_3. 0 DISABLED SWCLK disabled. 0x1 SWDIO SWDIO function select. 5 1 read-write ENABLED SWDIO enabled on pin PIO0_2. 0 DISABLED SWDIO disabled. 0x1 XTALIN XTALIN function select. 6 1 read-write ENABLED XTALIN enabled on pin PIO0_8. 0 DISABLED XTALIN disabled. 0x1 XTALOUT XTALOUT function select. 7 1 read-write ENABLED XTALOUT enabled on pin PIO0_9. 0 DISABLED XTALOUT disabled. 0x1 RESETN RESETN function select. 8 1 read-write ENABLED RESETN enabled on pin PIO0_5. 0 DISABLED RESETN disabled. 0x1 CLKIN CLKIN function select. 9 1 read-write ENABLED CLKIN enabled on pin PIO0_1. 0 DISABLED CLKIN disabled. 0x1 VDDCMP VDDCMP function select. 10 1 read-write ENABLED VDDCMP enabled on pin PIO0_6. 0 DISABLED VDDCMP disabled. 0x1 I2C0_SDA I2C0_SDA function select. 11 1 read-write ENABLED I2C0_SDA enabled on pin PIO0_11. 0 DISABLED I2C0_SDA disabled. 0x1 I2C0_SCL I2C0_SCL function select. 12 1 read-write ENABLED I2C0_SCL enabled on pin PIO0_10. 0 DISABLED I2C0_SCL disabled. 0x1 ADC_0 ADC_0 function select. 13 1 read-write ENABLED ADC_0 enabled on pin PIO0_7. 0 DISABLED ADC_0 disabled. 0x1 ADC_1 ADC_1 function select. 14 1 read-write ENABLED ADC_1 enabled on pin PIO0_6. 0 DISABLED ADC_1 disabled. 0x1 ADC_2 ADC_2 function select. 15 1 read-write ENABLED ADC_2 enabled on pin PIO0_14. 0 DISABLED ADC_2 disabled. 0x1 ADC_3 ADC_3 function select. 16 1 read-write ENABLED ADC_3 enabled on pin PIO0_23. 0 DISABLED ADC_3 disabled. 0x1 ADC_4 ADC_4 function select. 17 1 read-write ENABLED ADC_4 enabled on pin PIO0_22. 0 DISABLED ADC_4 disabled. 0x1 ADC_5 ADC_5 function select. 18 1 read-write ENABLED ADC_5 enabled on pin PIO0_21. 0 DISABLED ADC_5 disabled. 0x1 ADC_6 ADC_6 function select. 19 1 read-write ENABLED ADC_6 enabled on pin PIO0_20. 0 DISABLED ADC_6 disabled. 0x1 ADC_7 ADC_7 function select. 20 1 read-write ENABLED ADC_7 enabled on pin PIO0_19. 0 DISABLED ADC_7 disabled. 0x1 ADC_8 ADC_8 function select. 21 1 read-write ENABLED ADC_8 enabled on pin PIO0_18. 0 DISABLED ADC_8 disabled. 0x1 ADC_9 ADC_9 function select. 22 1 read-write ENABLED ADC_9 enabled on pin PIO0_17. 0 DISABLED ADC_9 disabled. 0x1 ADC_10 ADC_10 function select. 23 1 read-write ENABLED ADC_10 enabled on pin PIO0_13. 0 DISABLED ADC_10 disabled. 0x1 ADC_11 ADC_11 function select. 24 1 read-write ENABLED ADC_11 enabled on pin PIO0_4. 0 DISABLED ADC_11 disabled. 0x1 ADC0 LPC82x 12-bit ADC controller (ADC) ADC 0x4001C000 0 0x70 registers ADC0_SEQA 16 ADC0_SEQB 17 ADC0_THCMP 18 ADC0_OVR 19 CTRL ADC Control register. Contains the clock divide value, resolution selection, sampling time selection, and mode controls. 0 32 read-write 0 0x400004FF CLKDIV In synchronous mode only, the system clock is divided by this value plus one to produce the clock for the ADC converter, which should be less than or equal to 72 MHz. Typically, software should program the smallest value in this field that yields this maximum clock rate or slightly less, but in certain cases (such as a high-impedance analog source) a slower clock may be desirable. This field is ignored in the asynchronous operating mode. 0 8 read-write LPWRMODE The low-power ADC mode 10 1 read-write LPWRMODE_0 The low-power ADC mode is disabled. The analog circuitry remains activated even when no conversions are requested. 0 LPWRMODE_1 The low-power ADC mode is enabled. The analog circuitry is automatically powered-down when no conversions are taking place. When any (hardware or software) triggering event is detected, the analog circuitry is enabled. After the required start-up time, the requested conversion will be launched. Once the conversion completes, the analog-circuitry will again be powered-down provided no further conversions are pending. Using this mode can save an appreciable amount of current (approximately 2.5 mA) when conversions are required relatively infrequently. The penalty for using this mode is an approximately FIFTEEN ADC CLOCK delay (30 clocks in 10-bit mode), based on the frequency specified in the CLKDIV field, from the time the trigger event occurs until sampling of the A/D input commences. Note: This mode will NOT power-up the A/D if the ADC_ENA bit is low. 0x1 CALMODE Writing a '1' to this bit will initiate a sef-calibration cycle. This bit will be automatically cleared by hardware after the calibration cycle is complete. Note: Other bits of this register may be written to concurrently with setting this bit, however once this bit has been set no further writes to this register are permitted unitl the full calibration cycle has ended. 30 1 read-write 2 0x4 A,B SEQ_CTRL%s ADC Conversion Sequence-n control register: Controls triggering and channel selection for conversion sequence-n. Also specifies interrupt mode for sequence-n. 0x8 32 read-write 0 0xFC0C7FFF CHANNELS Selects which one or more of the ADC channels will be sampled and converted when this sequence is launched. A 1 in any bit of this field will cause the corresponding channel to be included in the conversion sequence, where bit 0 corresponds to channel 0, bit 1 to channel 1 and so forth. When this conversion sequence is triggered, either by a hardware trigger or via software command, ADC conversions will be performed on each enabled channel, in sequence, beginning with the lowest-ordered channel. This field can ONLY be changed while SEQA_ENA (bit 31) is LOW. It is allowed to change this field and set bit 31 in the same write. 0 12 read-write TRIGGER Selects which of the available hardware trigger sources will cause this conversion sequence to be initiated. Program the trigger input number in this field. See Table 476. In order to avoid generating a spurious trigger, it is recommended writing to this field only when SEQA_ENA (bit 31) is low. It is safe to change this field and set bit 31 in the same write. 12 3 read-write TRIGPOL Select the polarity of the selected input trigger for this conversion sequence. In order to avoid generating a spurious trigger, it is recommended writing to this field only when SEQA_ENA (bit 31) is low. It is safe to change this field and set bit 31 in the same write. 18 1 read-write NEGATIVE_EDGE Negative edge. A negative edge launches the conversion sequence on the selected trigger input. 0 POSITIVE_EDGE Positive edge. A positive edge launches the conversion sequence on the selected trigger input. 0x1 SYNCBYPASS Setting this bit allows the hardware trigger input to bypass synchronization flip-flop stages and therefore shorten the time between the trigger input signal and the start of a conversion. There are slightly different criteria for whether or not this bit can be set depending on the clock operating mode: Synchronous mode (the ASYNMODE in the CTRL register = 0): Synchronization may be bypassed (this bit may be set) if the selected trigger source is already synchronous with the main system clock (eg. coming from an on-chip, system-clock-based timer). Whether this bit is set or not, a trigger pulse must be maintained for at least one system clock period. Asynchronous mode (the ASYNMODE in the CTRL register = 1): Synchronization may be bypassed (this bit may be set) if it is certain that the duration of a trigger input pulse will be at least one cycle of the ADC clock (regardless of whether the trigger comes from and on-chip or off-chip source). If this bit is NOT set, the trigger pulse must at least be maintained for one system clock period. 19 1 read-write ENABLE_TRIGGER_SYNCH Enable trigger synchronization. The hardware trigger bypass is not enabled. 0 BYPASS_TRIGGER_SYNCH Bypass trigger synchronization. The hardware trigger bypass is enabled. 0x1 START Writing a 1 to this field will launch one pass through this conversion sequence. The behavior will be identical to a sequence triggered by a hardware trigger. Do not write 1 to this bit if the BURST bit is set. This bit is only set to a 1 momentarily when written to launch a conversion sequence. It will consequently always read back as a zero. 26 1 read-write BURST Writing a 1 to this bit will cause this conversion sequence to be continuously cycled through. Other sequence A triggers will be ignored while this bit is set. Repeated conversions can be halted by clearing this bit. The sequence currently in progress will be completed before conversions are terminated. Note that a new sequence could begin just before BURST is cleared. 27 1 read-write SINGLESTEP When this bit is set, a hardware trigger or a write to the START bit will launch a single conversion on the next channel in the sequence instead of the default response of launching an entire sequence of conversions. Once all of the channels comprising a sequence have been converted, a subsequent trigger will repeat the sequence beginning with the first enabled channel. Interrupt generation will still occur either after each individual conversion or at the end of the entire sequence, depending on the state of the MODE bit. 28 1 read-write LOWPRIO Set priority for sequence A. 29 1 read-write LOW_PRIORITY Low priority. Any B trigger which occurs while an A conversion sequence is active will be ignored and lost. 0 HIGH_PRIORITY High priority. Setting this bit to a 1 will permit any enabled B sequence trigger (including a B sequence software start) to immediately interrupt sequence A and launch a B sequence in it's place. The conversion currently in progress will be terminated. The A sequence that was interrupted will automatically resume after the B sequence completes. The channel whose conversion was terminated will be re-sampled and the conversion sequence will resume from that point. 0x1 MODE Indicates whether the primary method for retrieving conversion results for this sequence will be accomplished via reading the global data register (SEQA_GDAT) at the end of each conversion, or the individual channel result registers at the end of the entire sequence. Impacts when conversion-complete interrupt/DMA trigger for sequence-A will be generated and which overrun conditions contribute to an overrun interrupt as described below. 30 1 read-write END_OF_CONVERSION End of conversion. The sequence A interrupt/DMA trigger will be set at the end of each individual ADC conversion performed under sequence A. This flag will mirror the DATAVALID bit in the SEQA_GDAT register. The OVERRUN bit in the SEQA_GDAT register will contribute to generation of an overrun interrupt/DMA trigger if enabled. 0 END_OF_SEQUENCE End of sequence. The sequence A interrupt/DMA trigger will be set when the entire set of sequence-A conversions completes. This flag will need to be explicitly cleared by software or by the DMA-clear signal in this mode. The OVERRUN bit in the SEQA_GDAT register will NOT contribute to generation of an overrun interrupt/DMA trigger since it is assumed this register may not be utilized in this mode. 0x1 SEQ_ENA Sequence Enable. In order to avoid spuriously triggering the sequence, care should be taken to only set the SEQn_ENA bit when the selected trigger input is in its INACTIVE state (as defined by the TRIGPOL bit). If this condition is not met, the sequence will be triggered immediately upon being enabled. In order to avoid spuriously triggering the sequence, care should be taken to only set the SEQn_ENA bit when the selected trigger input is in its INACTIVE state (as defined by the TRIGPOL bit). If this condition is not met, the sequence will be triggered immediately upon being enabled. 31 1 read-write DISABLED Disabled. Sequence n is disabled. Sequence n triggers are ignored. If this bit is cleared while sequence n is in progress, the sequence will be halted at the end of the current conversion. After the sequence is re-enabled, a new trigger will be required to restart the sequence beginning with the next enabled channel. 0 ENABLED Enabled. Sequence n is enabled. 0x1 2 0x4 A,B SEQ_GDAT%s ADC Sequence-n Global Data register. This register contains the result of the most recent ADC conversion performed under sequence-n. 0x10 32 read-write 0 0xFC0FFFF0 RESULT This field contains the 12-bit ADC conversion result from the most recent conversion performed under conversion sequence associated with this register. The result is a binary fraction representing the voltage on the currently-selected input channel as it falls within the range of VREFP to VREFN. Zero in the field indicates that the voltage on the input pin was less than, equal to, or close to that on VREFN, while 0xFFF indicates that the voltage on the input was close to, equal to, or greater than that on VREFP. DATAVALID = 1 indicates that this result has not yet been read. 4 12 read-write THCMPRANGE Indicates whether the result of the last conversion performed was above, below or within the range established by the designated threshold comparison registers (THRn_LOW and THRn_HIGH). 16 2 read-only THCMPCROSS Indicates whether the result of the last conversion performed represented a crossing of the threshold level established by the designated LOW threshold comparison register (THRn_LOW) and, if so, in what direction the crossing occurred. 18 2 read-only CHN These bits contain the channel from which the RESULT bits were converted (e.g. 0000 identifies channel 0, 0001 channel 1, etc.). 26 4 read-only OVERRUN This bit is set if a new conversion result is loaded into the RESULT field before a previous result has been read - i.e. while the DATAVALID bit is set. This bit is cleared, along with the DATAVALID bit, whenever this register is read. This bit will contribute to an overrun interrupt/DMA trigger if the MODE bit (in SEQAA_CTRL) for the corresponding sequence is set to '0' (and if the overrun interrupt is enabled). 30 1 read-only DATAVALID This bit is set to '1' at the end of each conversion when a new result is loaded into the RESULT field. It is cleared whenever this register is read. This bit will cause a conversion-complete interrupt for the corresponding sequence if the MODE bit (in SEQA_CTRL) for that sequence is set to 0 (and if the interrupt is enabled). 31 1 read-only 12 0x4 DAT[%s] ADC Channel N Data register. This register contains the result of the most recent conversion completed on channel N. 0x20 32 read-only 0 0xFC0FFFF0 RESULT This field contains the 12-bit ADC conversion result from the last conversion performed on this channel. This will be a binary fraction representing the voltage on the AD0[n] pin, as it falls within the range of VREFP to VREFN. Zero in the field indicates that the voltage on the input pin was less than, equal to, or close to that on VREFN, while 0xFFF indicates that the voltage on the input was close to, equal to, or greater than that on VREFP. 4 12 read-only THCMPRANGE Threshold Range Comparison result. 0x0 = In Range: The last completed conversion was greater than or equal to the value programmed into the designated LOW threshold register (THRn_LOW) but less than or equal to the value programmed into the designated HIGH threshold register (THRn_HIGH). 0x1 = Below Range: The last completed conversion on was less than the value programmed into the designated LOW threshold register (THRn_LOW). 0x2 = Above Range: The last completed conversion was greater than the value programmed into the designated HIGH threshold register (THRn_HIGH). 0x3 = Reserved. 16 2 read-only THCMPCROSS Threshold Crossing Comparison result. 0x0 = No threshold Crossing detected: The most recent completed conversion on this channel had the same relationship (above or below) to the threshold value established by the designated LOW threshold register (THRn_LOW) as did the previous conversion on this channel. 0x1 = Reserved. 0x2 = Downward Threshold Crossing Detected. Indicates that a threshold crossing in the downward direction has occurred - i.e. the previous sample on this channel was above the threshold value established by the designated LOW threshold register (THRn_LOW) and the current sample is below that threshold. 0x3 = Upward Threshold Crossing Detected. Indicates that a threshold crossing in the upward direction has occurred - i.e. the previous sample on this channel was below the threshold value established by the designated LOW threshold register (THRn_LOW) and the current sample is above that threshold. 18 2 read-only CHANNEL This field is hard-coded to contain the channel number that this particular register relates to (i.e. this field will contain 0b0000 for the DAT0 register, 0b0001 for the DAT1 register, etc) 26 4 read-only OVERRUN This bit will be set to a 1 if a new conversion on this channel completes and overwrites the previous contents of the RESULT field before it has been read - i.e. while the DONE bit is set. This bit is cleared, along with the DONE bit, whenever this register is read or when the data related to this channel is read from either of the global SEQn_GDAT registers. This bit (in any of the 12 registers) will cause an overrun interrupt/DMA trigger to be asserted if the overrun interrupt is enabled. While it is allowed to include the same channels in both conversion sequences, doing so may cause erratic behavior of the DONE and OVERRUN bits in the data registers associated with any of the channels that are shared between the two sequences. Any erratic OVERRUN behavior will also affect overrun interrupt generation, if enabled. 30 1 read-only DATAVALID This bit is set to 1 when an ADC conversion on this channel completes. This bit is cleared whenever this register is read or when the data related to this channel is read from either of the global SEQn_GDAT registers. While it is allowed to include the same channels in both conversion sequences, doing so may cause erratic behavior of the DONE and OVERRUN bits in the data registers associated with any of the channels that are shared between the two sequences. Any erratic OVERRUN behavior will also affect overrun interrupt generation, if enabled. 31 1 read-only THR0_LOW ADC Low Compare Threshold register 0: Contains the lower threshold level for automatic threshold comparison for any channels linked to threshold pair 0. 0x50 32 read-write 0 0xFFF0 THRLOW Low threshold value against which ADC results will be compared 4 12 read-write THR1_LOW ADC Low Compare Threshold register 1: Contains the lower threshold level for automatic threshold comparison for any channels linked to threshold pair 1. 0x54 32 read-write 0 0xFFF0 THRLOW Low threshold value against which ADC results will be compared 4 12 read-write THR0_HIGH ADC High Compare Threshold register 0: Contains the upper threshold level for automatic threshold comparison for any channels linked to threshold pair 0. 0x58 32 read-write 0 0xFFF0 THRHIGH High threshold value against which ADC results will be compared 4 12 read-write THR1_HIGH ADC High Compare Threshold register 1: Contains the upper threshold level for automatic threshold comparison for any channels linked to threshold pair 1. 0x5C 32 read-write 0 0xFFF0 THRHIGH High threshold value against which ADC results will be compared 4 12 read-write CHAN_THRSEL ADC Channel-Threshold Select register. Specifies which set of threshold compare registers are to be used for each channel 0x60 32 read-write 0 0xFFF CH0_THRSEL Threshold select for channel 0. 0 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH1_THRSEL Threshold select for channel 1 1 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH2_THRSEL Threshold select for channel 2. 2 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH3_THRSEL Threshold select for channel 3. 3 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH4_THRSEL Threshold select for channel 4. 4 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH5_THRSEL Threshold select for channel 5. 5 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH6_THRSEL Threshold select for channel 6. 6 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH7_THRSEL Threshold select for channel 7. 7 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH8_THRSEL Threshold select for channel 8. 8 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH9_THRSEL Threshold select for channel 9. 9 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH10_THRSEL Threshold select for channel 10. 10 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 CH11_THRSEL Threshold select for channel 11. 11 1 read-write THRESHOLD0 Threshold 0. Results for this channel will be compared against the threshold levels indicated in the THR0_LOW and THR0_HIGH registers. 0 THRESHOLD1 Threshold 1. Results for this channel will be compared against the threshold levels indicated in the THR1_LOW and THR1_HIGH registers. 0x1 INTEN ADC Interrupt Enable register. This register contains enable bits that enable the sequence-A, sequence-B, threshold compare and data overrun interrupts to be generated. 0x64 32 read-write 0 0x7FFFFFF SEQA_INTEN Sequence A interrupt enable. 0 1 read-write DISABLED Disabled. The sequence A interrupt/DMA trigger is disabled. 0 ENABLED Enabled. The sequence A interrupt/DMA trigger is enabled and will be asserted either upon completion of each individual conversion performed as part of sequence A, or upon completion of the entire A sequence of conversions, depending on the MODE bit in the SEQA_CTRL register. 0x1 SEQB_INTEN Sequence B interrupt enable. 1 1 read-write DISABLED Disabled. The sequence B interrupt/DMA trigger is disabled. 0 ENABLED Enabled. The sequence B interrupt/DMA trigger is enabled and will be asserted either upon completion of each individual conversion performed as part of sequence B, or upon completion of the entire B sequence of conversions, depending on the MODE bit in the SEQB_CTRL register. 0x1 OVR_INTEN Overrun interrupt enable. 2 1 read-write DISABLED Disabled. The overrun interrupt is disabled. 0 ENABLED Enabled. The overrun interrupt is enabled. Detection of an overrun condition on any of the 12 channel data registers will cause an overrun interrupt/DMA trigger. In addition, if the MODE bit for a particular sequence is 0, then an overrun in the global data register for that sequence will also cause this interrupt/DMA trigger to be asserted. 0x1 ADCMPINTEN0 Threshold comparison interrupt enable for channel 0. 3 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN1 Channel 1 threshold comparison interrupt enable. 5 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN2 Channel 2 threshold comparison interrupt enable. 7 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN3 Channel 3 threshold comparison interrupt enable. 9 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN4 Channel 4 threshold comparison interrupt enable. 11 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN5 Channel 5 threshold comparison interrupt enable. 13 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN6 Channel 6 threshold comparison interrupt enable. 15 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN7 Channel 7 threshold comparison interrupt enable. 17 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN8 Channel 8 threshold comparison interrupt enable. 19 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN9 Channel 9 threshold comparison interrupt enable. 21 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN10 Channel 10 threshold comparison interrupt enable. 23 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 ADCMPINTEN11 Channel 11 threshold comparison interrupt enable. 25 2 read-write DISABLED Disabled. 0 OUTSIDE_THRESHOLD Outside threshold. 0x1 CROSSING_THRESHOLD Crossing threshold. 0x2 FLAGS ADC Flags register. Contains the four interrupt/DMA trigger flags and the individual component overrun and threshold-compare flags. (The overrun bits replicate information stored in the result registers). 0x68 32 read-write 0 0xF3FFFFFF THCMP0 Threshold comparison event on Channel 0. Set to 1 upon either an out-of-range result or a threshold-crossing result if enabled to do so in the INTEN register. This bit is cleared by writing a 1. 0 1 read-write THCMP1 Threshold comparison event on Channel 1. See description for channel 0. 1 1 read-write THCMP2 Threshold comparison event on Channel 2. See description for channel 0. 2 1 read-write THCMP3 Threshold comparison event on Channel 3. See description for channel 0. 3 1 read-write THCMP4 Threshold comparison event on Channel 4. See description for channel 0. 4 1 read-write THCMP5 Threshold comparison event on Channel 5. See description for channel 0. 5 1 read-write THCMP6 Threshold comparison event on Channel 6. See description for channel 0. 6 1 read-write THCMP7 Threshold comparison event on Channel 7. See description for channel 0. 7 1 read-write THCMP8 Threshold comparison event on Channel 8. See description for channel 0. 8 1 read-write THCMP9 Threshold comparison event on Channel 9. See description for channel 0. 9 1 read-write THCMP10 Threshold comparison event on Channel 10. See description for channel 0. 10 1 read-write THCMP11 Threshold comparison event on Channel 11. See description for channel 0. 11 1 read-write OVERRUN0 Mirrors the OVERRRUN status flag from the result register for ADC channel 0 12 1 read-only OVERRUN1 Mirrors the OVERRRUN status flag from the result register for ADC channel 1 13 1 read-only OVERRUN2 Mirrors the OVERRRUN status flag from the result register for ADC channel 2 14 1 read-only OVERRUN3 Mirrors the OVERRRUN status flag from the result register for ADC channel 3 15 1 read-only OVERRUN4 Mirrors the OVERRRUN status flag from the result register for ADC channel 4 16 1 read-only OVERRUN5 Mirrors the OVERRRUN status flag from the result register for ADC channel 5 17 1 read-only OVERRUN6 Mirrors the OVERRRUN status flag from the result register for ADC channel 6 18 1 read-only OVERRUN7 Mirrors the OVERRRUN status flag from the result register for ADC channel 7 19 1 read-only OVERRUN8 Mirrors the OVERRRUN status flag from the result register for ADC channel 8 20 1 read-only OVERRUN9 Mirrors the OVERRRUN status flag from the result register for ADC channel 9 21 1 read-only OVERRUN10 Mirrors the OVERRRUN status flag from the result register for ADC channel 10 22 1 read-only OVERRUN11 Mirrors the OVERRRUN status flag from the result register for ADC channel 11 23 1 read-only SEQA_OVR Mirrors the global OVERRUN status flag in the SEQA_GDAT register 24 1 read-only SEQB_OVR Mirrors the global OVERRUN status flag in the SEQB_GDAT register 25 1 read-only SEQA_INT Sequence A interrupt/DMA trigger. If the MODE bit in the SEQA_CTRL register is 0, this flag will mirror the DATAVALID bit in the sequence A global data register (SEQA_GDAT), which is set at the end of every ADC conversion performed as part of sequence A. It will be cleared automatically when the SEQA_GDAT register is read. If the MODE bit in the SEQA_CTRL register is 1, this flag will be set upon completion of an entire A sequence. In this case it must be cleared by writing a 1 to this SEQA_INT bit. This interrupt must be enabled in the INTEN register. 28 1 read-only SEQB_INT Sequence A interrupt/DMA trigger. If the MODE bit in the SEQB_CTRL register is 0, this flag will mirror the DATAVALID bit in the sequence A global data register (SEQB_GDAT), which is set at the end of every ADC conversion performed as part of sequence B. It will be cleared automatically when the SEQB_GDAT register is read. If the MODE bit in the SEQB_CTRL register is 1, this flag will be set upon completion of an entire B sequence. In this case it must be cleared by writing a 1 to this SEQB_INT bit. This interrupt must be enabled in the INTEN register. 29 1 read-only THCMP_INT Threshold Comparison Interrupt. This bit will be set if any of the THCMP flags in the lower bits of this register are set to 1 (due to an enabled out-of-range or threshold-crossing event on any channel). Each type of threshold comparison interrupt on each channel must be individually enabled in the INTEN register to cause this interrupt. This bit will be cleared when all of the individual threshold flags are cleared via writing 1s to those bits. 30 1 read-only OVR_INT Overrun Interrupt flag. Any overrun bit in any of the individual channel data registers will cause this interrupt. In addition, if the MODE bit in either of the SEQn_CTRL registers is 0 then the OVERRUN bit in the corresponding SEQn_GDAT register will also cause this interrupt. This interrupt must be enabled in the INTEN register. This bit will be cleared when all of the individual overrun bits have been cleared via reading the corresponding data registers. 31 1 read-only TRM ADC Startup register. 0x6C 32 read-write 0 0x20 VRANGE 2.4V to 3.6V Vdd range: This bit MUST be set to '1' if operation below 2.7V is to be used. Failure to set this bit will result in invalid ADC results. Note: This bit will not be spec'd on parts that do not support operation below 2.7V 5 1 read-write HIGH_VOLTAGE High voltage 0 LOW_VOLTAGE Low voltage 0x1 PMU LPC82x PMU PMU 0x40020000 0 0x18 registers PCON Power control register 0 32 read-write 0 0x90F PM Power mode 0 3 read-write DEFAULT Default. The part is in active or sleep mode. 0 DEEP_SLEEP_MODE Deep-sleep mode. ARM WFI will enter Deep-sleep mode. 0x1 POWER_DOWN_MODE Power-down mode. ARM WFI will enter Power-down mode. 0x2 DEEP_POWER_DOWN_MODE Deep power-down mode. ARM WFI will enter Deep-power down mode (ARM Cortex-M0+ core powered-down). 0x3 NODPD A 1 in this bit prevents entry to Deep power-down mode when 0x3 is written to the PM field above, the SLEEPDEEP bit is set, and a WFI is executed. This bit is cleared only by power-on reset, so writing a one to this bit locks the part in a mode in which Deep power-down mode is blocked. 3 1 read-write SLEEPFLAG Sleep mode flag 8 1 read-write ACTIVE_MODE Active mode. Read: No power-down mode entered. Part is in Active mode. Write: No effect. 0 LOW_POWER_MODE Low power mode. Read: Sleep, Deep-sleep or Power-down mode entered. Write: Writing a 1 clears the SLEEPFLAG bit to 0. 0x1 DPDFLAG Deep power-down flag 11 1 read-write NOT_DEEP_POWER_DOWN Not Deep power-down. Read: Deep power-down mode not entered. Write: No effect. 0 DEEP_POWER_DOWN Deep power-down. Read: Deep power-down mode entered. Write: Clear the Deep power-down flag. 0x1 4 0x4 GPREG[%s] General purpose register N 0x4 32 read-write 0 0xFFFFFFFF GPDATA Data retained during Deep power-down mode. 0 32 read-write DPDCTRL Deep power-down control register. Also includes bits for general purpose storage. 0x14 32 read-write 0 0xFFFFFFFF WAKEUPHYS WAKEUP pin hysteresis enable 0 1 read-write DISABLED Disabled. Hysteresis for WAKEUP pin disabled. 0 ENABLED Enabled. Hysteresis for WAKEUP pin enabled. 0x1 WAKEPAD_DISABLE WAKEUP pin disable. Setting this bit disables the wake-up pin, so it can be used for other purposes. Remark: Never set this bit if you intend to use a pin to wake up the part from Deep power-down mode. You can only disable the wake-up pin if the self wake-up timer is enabled and configured. Remark: Setting this bit is not necessary if Deep power-down mode is not used. 1 1 read-write ENABLED Enabled. The wake-up function is enabled on pin PIO0_4. 0 DISABLED Disabled. Setting this bit disables the wake-up function on pin PIO0_4. 0x1 LPOSCEN Enable the low-power oscillator for use with the 10 kHz self wake-up timer clock. You must set this bit if the CLKSEL bit in the self wake-up timer CTRL bit is set. Do not enable the low-power oscillator if the self wake-up timer is clocked by the divided IRC or the external clock input. 2 1 read-write DISABLED Disabled. 0 ENABLED Enabled. 0x1 LPOSCDPDEN causes the low-power oscillator to remain running during Deep power-down mode provided that bit 2 in this register is set as well. You must set this bit for the self wake-up timer to be able to wake up the part from Deep power-down mode. Remark: Do not set this bit unless you use the self wake-up timer with the low-power oscillator clock source to wake up from Deep power-down mode. 3 1 read-write DISABLED Disabled. 0 ENABLED Enabled. 0x1 WAKEUPCLKHYS External clock input for the self wake-up timer WKTCLKIN hysteresis enable. 4 1 read-write DISABLED Disabled. Hysteresis for WAKEUP clock pin disabled. 0 ENABLED Enabled. Hysteresis for WAKEUP clock pin enabled. 0x1 WAKECLKPAD_DISABLE Disable the external clock input for the self wake-up timer. Setting this bit enables the self wake-up timer clock pin WKTCLKLIN. To minimize power consumption, especially in deep power-down mode, disable this clock input when not using the external clock option for the self wake-up timer. 5 1 read-write DISABLED Disabled. Setting this bit disables external clock input on pin PIO0_28. 0 ENABLED Enabled. The external clock input for the self wake-up timer is enabled on pin PIO0_28. 0x1 GPDATA Data retained during Deep power-down mode. 6 26 read-write ACOMP LPC82x analog comparator ACOMP 0x40024000 0 0x8 registers CMP 11 CTRL Comparator control register 0 32 read-write 0 0x6B03F58 EDGESEL This field controls which edges on the comparator output set the COMPEDGE bit (bit 23 below): 3 2 read-write FALLING_EDGES Falling edges 0 RISING_EDGES Rising edges 0x1 BOTH_EDGES0 Both edges 0x2 BOTH_EDGES1 Both edges 0x3 COMPSA Comparator output control 6 1 read-write COMPSA_0 Comparator output is used directly. 0 COMPSA_1 Comparator output is synchronized to the bus clock for output to other modules. 0x1 COMP_VP_SEL Selects positive voltage input 8 3 read-write VOLTAGE_LADDER_OUTPUT VOLTAGE_LADDER_OUTPUT 0 ACMP_I1 ACMP_I1 0x1 ACMP_I2 ACMP_I2 0x2 ACMP_I3 ACMP_I3 0x3 ACMP_I4 ACMP_I4 0x4 BAND_GAP Band gap. Internal reference voltage. 0x5 ADC_0 ADC channel 0 input 0x6 COMP_VM_SEL Selects negative voltage input 11 3 read-write VOLTAGE_LADDER_OUTPUT VOLTAGE_LADDER_OUTPUT 0 ACMP_I1 ACMP_I1 0x1 ACMP_I2 ACMP_I2 0x2 ACMP_I3 ACMP_I3 0x3 ACMP_I4 ACMP_I4 0x4 BAND_GAP Band gap. Internal reference voltage. 0x5 ADC_0 ADC channel 0 input 0x6 EDGECLR Interrupt clear bit. To clear the COMPEDGE bit and thus negate the interrupt request, toggle the EDGECLR bit by first writing a 1 and then a 0. 20 1 read-write COMPSTAT Comparator status. This bit reflects the state of the comparator output. 21 1 read-write COMPEDGE Comparator edge-detect status. 23 1 read-write HYS Controls the hysteresis of the comparator. When the comparator is outputting a certain state, this is the difference between the selected signals, in the opposite direction from the state being output, that will switch the output. 25 2 read-write HYS_0 None (the output will switch as the voltages cross) 0 HYS_1 5 mv 0x1 HYS_2 10 mv 0x2 HYS_3 20 mv 0x3 LAD Voltage ladder register 0x4 32 read-write 0 0xFFFFFFFF LADEN Voltage ladder enable 0 1 read-write LADSEL Voltage ladder value. The reference voltage Vref depends on the LADREF bit below. 00000 = VSS 00001 = 1 x Vref/31 00010 = 2 x Vref/31 ... 11111 = Vref 1 5 read-write LADREF Selects the reference voltage Vref for the voltage ladder. 6 1 read-write LADREF_0 Supply pin VDD 0 LADREF_1 VDDCMP pin 0x1 INPUTMUX LPC82x Input multiplexing (INPUT MUX) INPUTMUX 0x40028000 0 0x4030 registers 18 0x4 DMA_ITRIG_INMUX[%s] Trigger select register for DMA channel 0 32 read-write 0xF 0xF INP Input mux register for trigger inputs 0 to 23 connected to DMA channel 0. Selects from ADC, SCT, ACMP, pin interrupts, and DMA requests. 0 4 read-write ADC_SEQA_IRQ ADC_SEQA_IRQ 0 ADC_SEQB_IRQ ADC_SEQB_IRQ 0x1 SCT_DMA0 SCT_DMA0 0x2 SCT_DMA1 SCT_DMA1 0x3 ACMP_O ACMP_O 0x4 PININT0 PININT0 0x5 PININT1 PININT1 0x6 DMA_INMUX_INMUX0 DMA trigger mux 0 0x7 DMA_INMUX_INMUX1 DMA trigger mux 1 0x8 2 0x4 DMA_INMUX_INMUX[%s] DMA output trigger selection to become DMA trigger 7 and DMA trigger 8 0x4000 32 read-write 0x1F 0x1F INP DMA trigger output number (decimal value) for DMA channel n (n = 0 to 17). 0 5 read-write 4 0x4 SCT0_INMUX[%s] input select register for SCT 0x4020 32 read-write 0xF 0xF INP_N Input mux register for SCT input n (n = 0 to 3). 0 = sct input 0 1=sct input 1 2= sct input 2 3= sct input 3 4= adc_thcmp_irq 5 = comparator out 6=arm_txev 7=debug_halted 0 4 read-write SCT_PIN0 SCT_PIN0 0x0 SCT_PIN1 SCT_PIN1 0x1 SCT_PIN2 SCT_PIN2 0x2 SCT_PIN3 SCT_PIN3 0x3 ADC_THCMP_IRQ ADC_THCMP_IRQ 0x4 ACMP_O ACMP_O 0x5 ARM_TXEV ARM_TXEV 0x6 DEBUG_HALTED DEBUG_HALTED 0x7 FLASH_CTRL LPC82x NVMC flash controller FLASH_CTRL 0x40040000 0 0xFEC registers FLASH 14 FLASHCFG Flash configuration register 0x10 32 read-write 0x1 0x3 FLASHTIM Flash memory access time. FLASHTIM +1 is equal to the number of system clocks used for flash access. 0 2 read-write ONE_SYSTEM_CLOCK_FLASH_ACCESS 1 system clock flash access time. 0 TWO_SYSTEM_CLOCK_FLASH_ACCESS 2 system clock flash access time. 0x1 FMSSTART Flash signature start address register 0x20 32 read-write 0 0x1FFFF START Signature generation start address (corresponds to AHB byte address bits[18:2]). 0 17 read-write FMSSTOP Flash signaure stop address register 0x24 32 read-write 0 0x8001FFFF STOPA Stop address for signature generation (the word specified by STOP is included in the address range). The address is in units of memory words, not bytes. 0 17 read-write STRTBIST When this bit is written to 1, signature generation starts. At the end of signature generation, this bit is automatically cleared. 31 1 read-write FMSW0 Flash signature generation result register returns the flash signature produced by the embedded signature generator.. 0x2C 32 read-only 0 0 SIG 32-bit signature. 0 32 read-only IOCON LPC82x I/O pin configuration (IOCON) IOCON 0x40044000 0 0x7C registers PIO0_17 Digital I/O control for pins PIO0_17 0 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_13 Digital I/O control for pins PIO0_13 0x4 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_12 Digital I/O control for pins PIO0_12 0x8 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_5 Digital I/O control for pins PIO0_5 0xC 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_4 Digital I/O control for pins PIO0_4 0x10 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_3 Digital I/O control for pins PIO0_3 0x14 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_2 Digital I/O control for pins PIO0_2 0x18 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_11 Digital I/O control for pins PIO0_11 0x1C 32 read-write 0x80 0xFFFFFFFF INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 I2CMODE Selects I2C mode. 8 2 read-write STANDARAD_I2C Standard mode/ Fast-mode I2C. 0 Standard_GPIO Standard GPIO functionality. Requires external pull-up for GPIO output function. 0x1 FAST_PLUS_I2C Fast-mode Plus I2C 0x2 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_10 Digital I/O control for pins PIO0_10 0x20 32 read-write 0x80 0xFFFFFFFF INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 I2CMODE Selects I2C mode. 8 2 read-write STANDARAD_I2C Standard mode/ Fast-mode I2C. 0 Standard_GPIO Standard GPIO functionality. Requires external pull-up for GPIO output function. 0x1 FAST_PLUS_I2C Fast-mode Plus I2C 0x2 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_16 Digital I/O control for pins PIO0_16 0x24 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_15 Digital I/O control for pins PIO0_15 0x28 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_1 Digital I/O control for pins PIO0_1 0x2C 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_9 Digital I/O control for pins PIO0_9 0x34 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_8 Digital I/O control for pins PIO0_8 0x38 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_7 Digital I/O control for pins PIO0_7 0x3C 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_6 Digital I/O control for pins PIO0_6 0x40 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_0 Digital I/O control for pins PIO0_0 0x44 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_14 Digital I/O control for pins PIO0_14 0x48 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_28 Digital I/O control for pins PIO0_28 0x50 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_27 Digital I/O control for pins PIO0_27 0x54 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_26 Digital I/O control for pins PIO0_26 0x58 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_25 Digital I/O control for pins PIO0_25 0x5C 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_24 Digital I/O control for pins PIO0_24 0x60 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_23 Digital I/O control for pins PIO0_23 0x64 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_22 Digital I/O control for pins PIO0_22 0x68 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_21 Digital I/O control for pins PIO0_21 0x6C 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_20 Digital I/O control for pins PIO0_20 0x70 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_19 Digital I/O control for pins PIO0_19 0x74 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 PIO0_18 Digital I/O control for pins PIO0_18 0x78 32 read-write 0x90 0xFFFFFFFF MODE Selects function mode (on-chip pull-up/pull-down resistor control). 3 2 read-write INACTIVE Inactive. Inactive (no pull-down/pull-up resistor enabled). 0 PULL_DOWN Pull-down. Pull-down resistor enabled. 0x1 PULL_UP Pull-up. Pull-up resistor enabled. 0x2 REPEATER Repeater. Repeater mode. 0x3 HYS Hysteresis. 5 1 read-write DISABLE Disable 0 ENABLE Enable 0x1 INV Invert input 6 1 read-write NOT_INVERTED Input not inverted (HIGH on pin reads as 1; LOW on pin reads as 0). 0 INVERTED Input inverted (HIGH on pin reads as 0, LOW on pin reads as 1). 0x1 OD Open-drain mode. 10 1 read-write DISABLE Disable. 0 ENABLED Open-drain mode enabled. Remark: This is not a true open-drain mode. 0x1 S_MODE Digital filter sample mode. 11 2 read-write S_MODE_0 Bypass input filter. 0 S_MODE_1 1 clock cycle. Input pulses shorter than one filter clock are rejected. 0x1 S_MODE_2 2 clock cycles. Input pulses shorter than two filter clocks are rejected. 0x2 S_MODE_3 3 clock cycles. Input pulses shorter than three filter clocks are rejected. 0x3 CLK_DIV Select peripheral clock divider for input filter sampling clock. Value 0x7 is reserved. 13 3 read-write CLK_DIV_0 IOCONCLKDIV0 0 CLK_DIV_1 IOCONCLKDIV1 0x1 CLK_DIV_2 IOCONCLKDIV2 0x2 CLK_DIV_3 IOCONCLKDIV3 0x3 CLK_DIV_4 IOCONCLKDIV4 0x4 CLK_DIV_5 IOCONCLKDIV5 0x5 CLK_DIV_6 IOCONCLKDIV6 0x6 SYSCON LPC82x System configuration (SYSCON) SYSCON 0x40048000 0 0x3FC registers BOD 13 SYSMEMREMAP System Remap register 0 32 read-write 0 0x3 MAP System memory remap. Value 0x3 is reserved. 0 2 read-write BOOT_LOADER_MODE Boot Loader Mode. Interrupt vectors are re-mapped to Boot ROM. 0 USER_RAM_MODE User RAM Mode. Interrupt vectors are re-mapped to Static RAM. 0x1 USER_FLASH_MODE User Flash Mode. Interrupt vectors are not re-mapped and reside in Flash. 0x2 PRESETCTRL Peripheral reset control register 0x4 32 read-write 0x2101DFFF 0x2101DFFF SPI0_RST_N SPI0 reset control. 0 1 read-write SPI0_RST_N_0 Assert the SPI0 reset. 0 SPI0_RST_N_1 Clear the SPI0 reset. 0x1 SPI1_RST_N SPI1 reset control. 1 1 read-write SPI1_RST_N_0 Assert the SPI1 reset. 0 SPI1_RST_N_1 Clear the SPI1 reset. 0x1 UARTFRG_RST_N USART fractional baud rate generator(UARTFRG) reset control. 2 1 read-write UARTFRG_RST_N_0 Assert the UARTFRG reset. 0 UARTFRG_RST_N_1 Clear the UARTFRG reset. 0x1 UART0_RST_N USART0 reset control. 3 1 read-write UART0_RST_N_0 Assert the USART0 reset. 0 UART0_RST_N_1 Clear the USART0 reset. 0x1 UART1_RST_N USART1 reset control. 4 1 read-write UART1_RST_N_0 Assert the USART1 reset. 0 UART1_RST_N_1 Clear the USART1 reset. 0x1 UART2_RST_N USART2 reset control. 5 1 read-write UART2_RST_N_0 Assert the USART2 reset. 0 UART2_RST_N_1 Clear the USART2 reset. 0x1 I2C0_RST_N I2C0 reset control. 6 1 read-write I2C0_RST_N_0 Assert the I2C0 reset. 0 I2C0_RST_N_1 Clear the I2C0 reset. 0x1 MRT_RST_N Multi-rate timer (MRT) reset control. 7 1 read-write MRT_RST_N_0 Assert the MRT reset. 0 MRT_RST_N_1 Clear the MRT reset. 0x1 SCT_RST_N SCT reset control. 8 1 read-write SCT_RST_N_0 Assert the SCT reset. 0 SCT_RST_N_1 Clear the SCT reset. 0x1 WKT_RST_N Self-wake-up timer (WKT) reset control. 9 1 read-write WKT_RST_N_0 Assert the WKT reset. 0 WKT_RST_N_1 Clear the WKT reset. 0x1 GPIO_RST_N GPIO and GPIO pin interrupt reset control. 10 1 read-write GPIO_RST_N_0 Assert the GPIO reset. 0 GPIO_RST_N_1 Clear the GPIO reset. 0x1 FLASH_RST_N Flash controller reset control. 11 1 read-write FLASH_RST_N_0 Assert the flash controller reset. 0 FLASH_RST_N_1 Clear the flash controller reset. 0x1 ACMP_RST_N Analog comparator reset control. 12 1 read-write ACMP_RST_N_0 Assert the analog comparator reset. 0 ACMP_RST_N_1 Clear the analog comparator controller reset. 0x1 I2C1_RST_N I2C1 reset control. 14 1 read-write I2C1_RST_N_0 Assert the I2C1 reset. 0 I2C1_RST_N_1 Clear the I2C1 reset. 0x1 I2C2_RST_N I2C2 reset control. 15 1 read-write I2C2_RST_N_0 Assert the I2C2 reset. 0 I2C2_RST_N_1 Clear the I2C2 reset. 0x1 I2C3_RST_N I2C3 reset control. 16 1 read-write I2C3_RST_N_0 Assert the I2C3 reset. 0 I2C3_RST_N_1 Clear the I2C3 reset. 0x1 ADC_RST_N ADC reset control. 24 1 read-write ADC_RST_N_0 Assert the ADC reset. 0 ADC_RST_N_1 Clear the ADC reset. 0x1 DMA_RST_N DMA reset control. 29 1 read-write DMA_RST_N_0 Assert the DMA reset. 0 DMA_RST_N_1 Clear the DMA reset. 0x1 SYSPLLCTRL PLL control 0x8 32 read-write 0 0x7F MSEL Feedback divider value. The division value M is the programmed MSEL value + 1. 00000: Division ratio M = 1 to 11111: Division ratio M = 32 0 5 read-write PSEL Post divider ratio P. The division ratio is 2 x P. 5 2 read-write PSEL_0 P = 1 0 PSEL_1 P = 2 0x1 PSEL_2 P = 4 0x2 PSEL_3 P = 8 0x3 SYSPLLSTAT PLL status 0xC 32 read-only 0 0x1 LOCK PLL0 lock indicator 0 1 read-only SYSOSCCTRL system oscillator control 0x20 32 read-write 0 0xFFFFFFFF BYPASS Bypass system oscillator 0 1 read-write FREQ_RANGE oscillator low / high transconductance selection input (Active High) 1-20MHz '0' : 15-50MHz '1' 1 1 read-write WDTOSCCTRL Watchdog oscillator control 0x24 32 read-write 0 0xFFFFFFFF DIVSEL Select divider for Fclkana. wdt_osc_clk = Fclkana/ (2 x (1 + DIVSEL)) 00000: 2 x (1 + DIVSEL) = 2 00001: 2 x (1 + DIVSEL) = 4 to 11111: 2 x (1 + DIVSEL) = 64 0 5 read-write FREQSEL Frequency select. Selects the frequency of the oscillator. 0x00 = invalid setting when watchdog oscillator is running 0x1 = 0.6 MHz 0x2 = 1.05 MHz 0x3 = 1.4 MHz 0x4 = 1.75 MHz 0x5 = 2.1 MHz 0x6 = 2.4 MHz 0x7 = 2.7 MHz 0x8 = 3.0 MHz 0x9 = 3.25 MHz 0xA = 3.5 MHz 0xB = 3.75 MHz 0xC = 4.0 MHz 0xD = 4.2 MHz 0xE = 4.4 MHz 0xF = 4.6 MHz 5 4 read-write IRCCTRL IRC control 0x28 32 read-write 0x80 0xFF TRIM Trim value 0 8 read-write SYSRSTSTAT System reset status register 0x30 32 read-write 0 0x1F POR POR reset status. 0 1 read-write POR_0 No POR detected. 0 POR_1 POR detected. Writing a one clears this reset. 0x1 EXTRST Status of the external RESET pin. External reset status. 1 1 read-write EXTRST_0 No reset event detected. 0 EXTRST_1 Reset detected. Writing a one clears this reset. 0x1 WDT Status of the Watchdog reset. 2 1 read-write WDT_0 No WDT reset detected. 0 WDT_1 WDT reset detected. Writing a one clears this reset. 0x1 BOD Status of the Brown-out detect reset. 3 1 read-write BOD_0 No BOD reset detected. 0 BOD_1 BOD reset detected. Writing a one clears this reset. 0x1 SYSRST Status of the software system reset. 4 1 read-write SYSRST_0 No System reset detected. 0 SYSRST_1 System reset detected. Writing a one clears this reset. 0x1 SYSPLLCLKSEL System PLL clock source select register 0x40 32 read-write 0 0x3 SEL System PLL clock source 0 2 read-write IRC IRC 0 SYSOSC Crystal Oscillator (SYSOSC) 0x1 CLKIN CLKIN. External clock input. 0x3 SYSPLLCLKUEN System PLL clock source update enable register 0x44 32 read-write 0 0x1 ENA Enable system PLL clock source update 0 1 read-write NO_CHANGE no change 0 UPDATED update clock source 0x1 MAINCLKSEL Main clock source select 0x70 32 read-write 0 0x3 SEL Clock source for main clock. 0 2 read-write IRC_Osc IRC Oscillator. 0 PLL_in PLL input. 0x1 WDTOSC Watchdog oscillator. 0x2 PLL_out PLL output. 0x3 MAINCLKUEN Main clock source update enable 0x74 32 read-write 0 0x1 ENA Enable main clock source update. 0 1 read-write ENA_0 No change. 0 ENA_1 Update clock source. 0x1 SYSAHBCLKDIV System clock divider 0x78 32 read-write 0x1 0xFF DIV System AHB clock divider values 0: System clock disabled. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write SYSAHBCLKCTRL System clock control 0x80 32 read-write 0xDF 0x25EFFFFF SYS Enables the clock for the AHB, the APB bridge, the Cortex-M0+ core clocks, SYSCON, and the PMU. This bit is read only and always reads as 1. 0 1 read-write ROM Enables clock for ROM. 1 1 read-write ROM_0 Disable. 0 ROM_1 Enable. 0x1 RAM0_1 Enables clock for SRAM0 and SRAM1. 2 1 read-write RAM0_1_0 Disable. 0 RAM0_1_1 Enable. 0x1 FLASHREG Enables clock for flash register interface. 3 1 read-write FLASHREG_0 Disable. 0 FLASHREG_1 Enable. 0x1 FLASH Enables clock for flash. 4 1 read-write FLASH_0 Disable. 0 FLASH_1 Enable. 0x1 I2C0 Enables clock for I2C0. 5 1 read-write I2C0_0 Disable. 0 I2C0_1 Enable. 0x1 GPIO Enables clock for GPIO port registers and GPIO pin interrupt registers. 6 1 read-write GPIO_0 Disable. 0 GPIO_1 Enable. 0x1 SWM Enables clock for switch matrix. 7 1 read-write SWM_0 Disable. 0 SWM_1 Enable. 0x1 SCT Enables clock for state configurable timer SCTimer/PWM. 8 1 read-write SCT_0 Disable. 0 SCT_1 Enable. 0x1 WKT Enables clock for self-wake-up timer. 9 1 read-write WKT_0 Disable. 0 WKT_1 Enable. 0x1 MRT Enables clock for multi-rate timer. 10 1 read-write MRT_0 Disable. 0 MRT_1 Enable. 0x1 SPI0 Enables clock for SPI0. 11 1 read-write SPI0_0 Disable. 0 SPI0_1 Enable. 0x1 SPI1 Enables clock for SPI1. 12 1 read-write SPI1_0 Disable. 0 SPI1_1 Enable. 0x1 CRC Enables clock for CRC. 13 1 read-write CRC_0 Disable. 0 CRC_1 Enable. 0x1 UART0 Enables clock for USART0. 14 1 read-write UART0_0 Disable. 0 UART0_1 Enable. 0x1 UART1 Enables clock for USART1. 15 1 read-write UART1_0 Disable. 0 UART1_1 Enable. 0x1 UART2 Enables clock for USART2. 16 1 read-write UART2_0 Disable. 0 UART2_1 Enable. 0x1 WWDT Enables clock for WWDT. 17 1 read-write WWDT_0 Disable. 0 WWDT_1 Enable. 0x1 IOCON Enables clock for IOCON block. 18 1 read-write IOCON_0 Disable. 0 IOCON_1 Enable. 0x1 ACMP Enables clock to analog comparator. 19 1 read-write ACMP_0 Disable. 0 ACMP_1 Enable. 0x1 I2C1 Enables clock to I2C1. 21 1 read-write I2C1_0 Disable. 0 I2C1_1 Enable. 0x1 I2C2 Enables clock to I2C2. 22 1 read-write I2C2_0 Disable. 0 I2C2_1 Enable. 0x1 I2C3 Enables clock to I2C3. 23 1 read-write I2C3_0 Disable. 0 I2C3_1 Enable. 0x1 ADC Enables clock to ADC. 24 1 read-write ADC_0 Disable. 0 ADC_1 Enable. 0x1 MTB Enables clock to micro-trace buffer control registers.Turn on this clock when using the micro-trace buffer for debug purposes. 26 1 read-write MTB_0 Disable. 0 MTB_1 Enable. 0x1 DMA Enables clock to DMA. 29 1 read-write DMA_0 Disable. 0 DMA_1 Enable. 0x1 UARTCLKDIV USART clock divider 0x94 32 read-write 0 0xFF DIV USART fractional baud rate generator clock divider values. 0: Clock disabled. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write CLKOUTSEL CLKOUT clock source select 0xE0 32 read-write 0 0xFFFFFFFF SEL CLKOUT clock source. 0 2 read-write IRC_osc IRC oscillator 0 SYSOSC Crystal oscillator (SYSOSC) 0x1 WDTOSC Watchdog oscillator 0x2 MAIN_CLK Main clock 0x3 CLKOUTUEN CLKOUT clock source update enable 0xE4 32 read-write 0 0x1 ENA Enable CLKOUT clock source update. 0 1 read-write ENA_0 No change 0 ENA_1 Update clock source 0x1 CLKOUTDIV PLL control 0xE8 32 read-write 0 0xFF DIV CLKOUT clock divider values. 0: Disable CLKOUT clock divider 1: Divide by 1 to 255: Divide by 255 0 8 read-write UARTFRGDIV USART1 to USART4 common fractional generator divider value 0xF0 32 read-write 0 0xFF DIV Denominator of the fractional divider. DIV is equal to the programmed value +1. Always set to 0xFF to use with the fractional baud rate generator. 0 8 read-write UARTFRGMULT USART common fractional generator divider value 0xF4 32 read-write 0 0xFF MULT Numerator of the fractional divider. MULT is equal to the programmed value. 0 8 read-write EXTTRACECMD External trace buffer command register 0xFC 32 read-write 0 0x3 START Trace start command. Writing a one to this bit sets the TSTART signal to the MTB to HIGH and starts tracing if the TSTARTEN bit in the MTB master register is set to one as well. 0 1 read-write STOP Trace stop command. Writing a one to this bit sets the TSTOP signal in the MTB to HIGH and stops tracing if the TSTOPEN bit in the MTB master register is set to one as well. 1 1 read-write PIOPORCAP0 POR captured PIO status 0 0x100 32 read-write 0 0 PIOSTAT State of PIO0_17 through PIO0_0 at power-on reset 0 18 read-only IOCONCLKDIV6 Peripheral clock 6 to the IOCON block for programmable glitch filter 0x134 32 read-write 0 0xFFFFFFFF DIV IOCON glitch filter clock divider values 0: Disable IOCONFILTR_PCLK. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write IOCONCLKDIV5 Peripheral clock 6 to the IOCON block for programmable glitch filter 0x138 32 read-write 0 0xFFFFFFFF DIV IOCON glitch filter clock divider values 0: Disable IOCONFILTR_PCLK. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write IOCONCLKDIV4 Peripheral clock 4 to the IOCON block for programmable glitch filter 0x13C 32 read-write 0 0xFFFFFFFF DIV IOCON glitch filter clock divider values 0: Disable IOCONFILTR_PCLK. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write IOCONCLKDIV3 Peripheral clock 3 to the IOCON block for programmable glitch filter 0x140 32 read-write 0 0xFFFFFFFF DIV IOCON glitch filter clock divider values 0: Disable IOCONFILTR_PCLK. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write IOCONCLKDIV2 Peripheral clock 2 to the IOCON block for programmable glitch filter 0x144 32 read-write 0 0xFFFFFFFF DIV IOCON glitch filter clock divider values 0: Disable IOCONFILTR_PCLK. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write IOCONCLKDIV1 Peripheral clock 1 to the IOCON block for programmable glitch filter 0x148 32 read-write 0 0xFFFFFFFF DIV IOCON glitch filter clock divider values 0: Disable IOCONFILTR_PCLK. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write IOCONCLKDIV0 Peripheral clock 0 to the IOCON block for programmable glitch filter 0x14C 32 read-write 0 0xFFFFFFFF DIV IOCON glitch filter clock divider values 0: Disable IOCONFILTR_PCLK. 1: Divide by 1. to 255: Divide by 255. 0 8 read-write BODCTRL BOD control register 0x150 32 read-write 0 0x1F BODRSTLEV BOD reset level 0 2 read-write LEVEL_1 Level 1 0x1 LEVEL_2 Level 2 0x2 LEVEL_3 Level 3 0x3 BODINTVAL BOD interrupt level 2 2 read-write LEVEL_1 Level 1 0x1 LEVEL_2 Level 2 0x2 LEVEL_3 Level 3 0x3 BODRSTENA BOD reset enable 4 1 read-write DISABLE Disable reset function. 0 ENABLE Enable reset function. 0x1 SYSTCKCAL System tick timer calibration register 0x154 32 read-write 0 0x3FFFFFF CAL System tick timer calibration value. 0 26 read-write IRQLATENCY IRQ latency register 0x170 32 read-write 0x10 0xFF LATENCY 8-bit latency value. 0 8 read-write NMISRC NMI source selection register 0x174 32 read-write 0 0x8000001F IRQN The IRQ number of the interrupt that acts as the Non-Maskable Interrupt (NMI) if bit 31 is 1 0 5 read-write NMIEN Write a 1 to this bit to enable the Non-Maskable Interrupt (NMI) source selected by bits 4:0. 31 1 read-write 8 0x4 PINTSEL[%s] Pin interrupt select registers N 0x178 32 read-write 0 0x3F INTPIN Pin number select for pin interrupt or pattern match engine input. (PIO0_0 to PIO0_28 correspond to numbers 0 to 28). 0 6 read-write STARTERP0 Start logic 0 pin wake-up enable register 0 0x204 32 read-write 0 0xFF PINT0 GPIO pin interrupt 0 wake-up 0 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PINT1 GPIO pin interrupt 1 wake-up 1 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PINT2 GPIO pin interrupt 2 wake-up 2 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PINT3 GPIO pin interrupt 3 wake-up 3 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PINT4 GPIO pin interrupt 4 wake-up 4 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PINT5 GPIO pin interrupt 5 wake-up 5 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PINT6 GPIO pin interrupt 6 wake-up 6 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PINT7 GPIO pin interrupt 7 wake-up 7 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 STARTERP1 Start logic 1 interrupt wake-up enable register 0x214 32 read-write 0 0x60B1BB SPI0 SPI0 interrupt wake-up 0 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 SPI1 SPI1 interrupt wake-up 1 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 USART0 USART0 interrupt wake-up. Configure USART in synchronous slave mode. 3 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 USART1 USART1 interrupt wake-up. Configure USART in synchronous slave mode. 4 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 USART2 USART2 interrupt wake-up. Configure USART in synchronous slave mode. 5 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 I2C1 I2C1 interrupt wake-up. 7 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 I2C0 I2C0 interrupt wake-up. 8 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 WWDT WWDT interrupt wake-up 12 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 BOD BOD interrupt wake-up 13 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 WKT Self-wake-up timer interrupt wake-up 15 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 I2C2 I2C2 interrupt wake-up 21 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 I2C3 I2C3 interrupt wake-up 22 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PDSLEEPCFG Deep-sleep configuration register 0x230 32 read-write 0xFFFF 0xFFFF BOD_PD BOD power-down control for Deep-sleep and Power-down mode 3 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 WDTOSC_PD Watchdog oscillator power-down control for Deep-sleep and Power-down mode. Changing this bit to powered-down has no effect when the LOCK bit in the WWDT MOD register is set. In this case, the watchdog oscillator is always running. 6 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PDAWAKECFG Wake-up configuration register 0x234 32 read-write 0xEDF0 0xFFFF IRCOUT_PD IRC oscillator output wake-up configuration 0 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 IRC_PD IRC oscillator power-down wake-up configuration 1 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 FLASH_PD Flash wake-up configuration 2 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 BOD_PD BOD wake-up configuration 3 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 ADC_PD ADC wake-up configuration 4 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 SYSOSC_PD Crystal oscillator wake-up configuration 5 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 WDTOSC_PD Watchdog oscillator wake-up configuration. Changing this bit to powered-down has no effect when the LOCK bit in the WWDT MOD register is set. In this case, the watchdog oscillator is always running 6 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 SYSPLL_PD System PLL wake-up configuration 7 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 ACMP Analog comparator wake-up configuration 15 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 PDRUNCFG Power configuration register 0x238 32 read-write 0xEDF0 0xFFFFFFFF IRCOUT_PD IRC oscillator output wake-up configuration 0 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 IRC_PD IRC oscillator power-down wake-up configuration 1 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 FLASH_PD Flash wake-up configuration 2 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 BOD_PD BOD wake-up configuration 3 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 ADC_PD ADC wake-up configuration 4 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 SYSOSC_PD Crystal oscillator wake-up configuration 5 1 read-write POWERED powered 0 POWERED_DOWN powered down 0x1 WDTOSC_PD Watchdog oscillator wake-up configuration. Changing this bit to powered-down has no effect when the LOCK bit in the WWDT MOD register is set. In this case, the watchdog oscillator is always running 6 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 SYSPLL_PD System PLL wake-up configuration 7 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 ACMP Analog comparator wake-up configuration 15 1 read-write DISABLED Disabled 0 ENABLED Enabled 0x1 DEVICE_ID Part ID register 0x3F8 32 read-only 0 0xFFFFFFFF DEVICEID Part ID 0 32 read-only I2C0 LPC82x I2C-bus interfaces I2C I2C 0x40050000 0 0x84 registers I2C0 8 CFG Configuration for shared functions. 0 32 read-write 0 0x3F MSTEN Master Enable. When disabled, configurations settings for the Master function are not changed, but the Master function is internally reset. 0 1 read-write DISABLED Disabled. The I2C Master function is disabled. 0 ENABLED Enabled. The I2C Master function is enabled. 0x1 SLVEN Slave Enable. When disabled, configurations settings for the Slave function are not changed, but the Slave function is internally reset. 1 1 read-write DISABLED Disabled. The I2C slave function is disabled. 0 ENABLED Enabled. The I2C slave function is enabled. 0x1 MONEN Monitor Enable. When disabled, configurations settings for the Monitor function are not changed, but the Monitor function is internally reset. 2 1 read-write DISABLED Disabled. The I2C Monitor function is disabled. 0 ENABLED Enabled. The I2C Monitor function is enabled. 0x1 TIMEOUTEN I2C bus Time-out Enable. When disabled, the time-out function is internally reset. 3 1 read-write DISABLED Disabled. Time-out function is disabled. 0 ENABLED Enabled. Time-out function is enabled. Both types of time-out flags will be generated and will cause interrupts if they are enabled. Typically, only one time-out will be used in a system. 0x1 MONCLKSTR Monitor function Clock Stretching. 4 1 read-write DISABLED Disabled. The Monitor function will not perform clock stretching. Software or DMA may not always be able to read data provided by the Monitor function before it is overwritten. This mode may be used when non-invasive monitoring is critical. 0 ENABLED Enabled. The Monitor function will perform clock stretching in order to ensure that software or DMA can read all incoming data supplied by the Monitor function. 0x1 STAT Status register for Master, Slave, and Monitor functions. 0x4 32 read-write 0x801 0x30FFF5F MSTPENDING Master Pending. Indicates that the Master is waiting to continue communication on the I2C-bus (pending) or is idle. When the master is pending, the MSTSTATE bits indicate what type of software service if any the master expects. This flag will cause an interrupt when set if, enabled via the INTENSET register. The MSTPENDING flag is not set when the DMA is handling an event (if the MSTDMA bit in the MSTCTL register is set). If the master is in the idle state, and no communication is needed, mask this interrupt. 0 1 read-only IN_PROGRESS In progress. Communication is in progress and the Master function is busy and cannot currently accept a command. 0 PENDING Pending. The Master function needs software service or is in the idle state. If the master is not in the idle state, it is waiting to receive or transmit data or the NACK bit. 0x1 MSTSTATE Master State code. The master state code reflects the master state when the MSTPENDING bit is set, that is the master is pending or in the idle state. Each value of this field indicates a specific required service for the Master function. All other values are reserved. See Table 400 for details of state values and appropriate responses. 1 3 read-only IDLE Idle. The Master function is available to be used for a new transaction. 0 RECEIVE_READY Receive ready. Received data available (Master Receiver mode). Address plus Read was previously sent and Acknowledged by slave. 0x1 TRANSMIT_READY Transmit ready. Data can be transmitted (Master Transmitter mode). Address plus Write was previously sent and Acknowledged by slave. 0x2 NACK_ADDRESS NACK Address. Slave NACKed address. 0x3 NACK_DATA NACK Data. Slave NACKed transmitted data. 0x4 MSTARBLOSS Master Arbitration Loss flag. This flag can be cleared by software writing a 1 to this bit. It is also cleared automatically a 1 is written to MSTCONTINUE. 4 1 read-write NO_LOSS No Arbitration Loss has occurred. 0 ARBITRATION_LOSS Arbitration loss. The Master function has experienced an Arbitration Loss. At this point, the Master function has already stopped driving the bus and gone to an idle state. Software can respond by doing nothing, or by sending a Start in order to attempt to gain control of the bus when it next becomes idle. 0x1 MSTSTSTPERR Master Start/Stop Error flag. This flag can be cleared by software writing a 1 to this bit. It is also cleared automatically a 1 is written to MSTCONTINUE. 6 1 read-write NO_ERROR No Start/Stop Error has occurred. 0 ERROR The Master function has experienced a Start/Stop Error. A Start or Stop was detected at a time when it is not allowed by the I2C specification. The Master interface has stopped driving the bus and gone to an idle state, no action is required. A request for a Start could be made, or software could attempt to insure that the bus has not stalled. 0x1 SLVPENDING Slave Pending. Indicates that the Slave function is waiting to continue communication on the I2C-bus and needs software service. This flag will cause an interrupt when set if enabled via INTENSET. The SLVPENDING flag is not set when the DMA is handling an event (if the SLVDMA bit in the SLVCTL register is set). The SLVPENDING flag is read-only and is automatically cleared when a 1 is written to the SLVCONTINUE bit in the SLVCTL register. The point in time when SlvPending is set depends on whether the I2C interface is in HSCAPABLE mode. See Section 25.7.2.2.2. When the I2C interface is configured to be HSCAPABLE, HS master codes are detected automatically. Due to the requirements of the HS I2C specification, slave addresses must also be detected automatically, since the address must be acknowledged before the clock can be stretched. 8 1 read-only IN_PROGRESS In progress. The Slave function does not currently need service. 0 PENDING Pending. The Slave function needs service. Information on what is needed can be found in the adjacent SLVSTATE field. 0x1 SLVSTATE Slave State code. Each value of this field indicates a specific required service for the Slave function. All other values are reserved. See Table 401 for state values and actions. note that the occurrence of some states and how they are handled are affected by DMA mode and Automatic Operation modes. 9 2 read-only SLAVE_ADDRESS Slave address. Address plus R/W received. At least one of the four slave addresses has been matched by hardware. 0 SLAVE_RECEIVE Slave receive. Received data is available (Slave Receiver mode). 0x1 SLAVE_TRANSMIT Slave transmit. Data can be transmitted (Slave Transmitter mode). 0x2 SLVNOTSTR Slave Not Stretching. Indicates when the slave function is stretching the I2C clock. This is needed in order to gracefully invoke Deep Sleep or Power-down modes during slave operation. This read-only flag reflects the slave function status in real time. 11 1 read-only STRETCHING Stretching. The slave function is currently stretching the I2C bus clock. Deep-Sleep or Power-down mode cannot be entered at this time. 0 NOT_STRETCHING Not stretching. The slave function is not currently stretching the I 2C bus clock. Deep-sleep or Power-down mode could be entered at this time. 0x1 SLVIDX Slave address match Index. This field is valid when the I2C slave function has been selected by receiving an address that matches one of the slave addresses defined by any enabled slave address registers, and provides an identification of the address that was matched. It is possible that more than one address could be matched, but only one match can be reported here. 12 2 read-only ADDRESS0 Address 0. Slave address 0 was matched. 0 ADDRESS1 Address 1. Slave address 1 was matched. 0x1 ADDRESS2 Address 2. Slave address 2 was matched. 0x2 ADDRESS3 Address 3. Slave address 3 was matched. 0x3 SLVSEL Slave selected flag. SLVSEL is set after an address match when software tells the Slave function to acknowledge the address, or when the address has been automatically acknowledged. It is cleared when another address cycle presents an address that does not match an enabled address on the Slave function, when slave software decides to NACK a matched address, when there is a Stop detected on the bus, when the master NACKs slave data, and in some combinations of Automatic Operation. SLVSEL is not cleared if software NACKs data. 14 1 read-only NOT_SELECTED Not selected. The Slave function is not currently selected. 0 SELECTED Selected. The Slave function is currently selected. 0x1 SLVDESEL Slave Deselected flag. This flag will cause an interrupt when set if enabled via INTENSET. This flag can be cleared by writing a 1 to this bit. 15 1 read-write NOT_DESELECTED Not deselected. The Slave function has not become deselected. This does not mean that it is currently selected. That information can be found in the SLVSEL flag. 0 DESELECTED Deselected. The Slave function has become deselected. This is specifically caused by the SLVSEL flag changing from 1 to 0. See the description of SLVSEL for details on when that event occurs. 0x1 MONRDY Monitor Ready. This flag is cleared when the MONRXDAT register is read. 16 1 read-only NO_DATA No data. The Monitor function does not currently have data available. 0 DATA_WAITING Data waiting. The Monitor function has data waiting to be read. 0x1 MONOV Monitor Overflow flag. 17 1 read-write NO_OVERRUN No overrun. Monitor data has not overrun. 0 OVERRUN Overrun. A Monitor data overrun has occurred. This can only happen when Monitor clock stretching not enabled via the MONCLKSTR bit in the CFG register. Writing 1 to this bit clears the flag. 0x1 MONACTIVE Monitor Active flag. Indicates when the Monitor function considers the I 2C bus to be active. Active is defined here as when some Master is on the bus: a bus Start has occurred more recently than a bus Stop. 18 1 read-only INACTIVE Inactive. The Monitor function considers the I2C bus to be inactive. 0 ACTIVE Active. The Monitor function considers the I2C bus to be active. 0x1 MONIDLE Monitor Idle flag. This flag is set when the Monitor function sees the I2C bus change from active to inactive. This can be used by software to decide when to process data accumulated by the Monitor function. This flag will cause an interrupt when set if enabled via the INTENSET register. The flag can be cleared by writing a 1 to this bit. 19 1 read-write NOT_IDLE Not idle. The I2C bus is not idle, or this flag has been cleared by software. 0 IDLE Idle. The I2C bus has gone idle at least once since the last time this flag was cleared by software. 0x1 EVENTTIMEOUT Event Time-out Interrupt flag. Indicates when the time between events has been longer than the time specified by the TIMEOUT register. Events include Start, Stop, and clock edges. The flag is cleared by writing a 1 to this bit. No time-out is created when the I2C-bus is idle. 24 1 read-write NO_TIMEOUT No time-out. I2C bus events have not caused a time-out. 0 EVEN_TIMEOUT Event time-out. The time between I2C bus events has been longer than the time specified by the TIMEOUT register. 0x1 SCLTIMEOUT SCL Time-out Interrupt flag. Indicates when SCL has remained low longer than the time specific by the TIMEOUT register. The flag is cleared by writing a 1 to this bit. 25 1 read-write NO_TIMEOUT No time-out. SCL low time has not caused a time-out. 0 TIMEOUT Time-out. SCL low time has caused a time-out. 0x1 INTENSET Interrupt Enable Set and read register. 0x8 32 read-write 0 0x30B8951 MSTPENDINGEN Master Pending interrupt Enable. 0 1 read-write DISABLED Disabled. The MstPending interrupt is disabled. 0 ENABLED Enabled. The MstPending interrupt is enabled. 0x1 MSTARBLOSSEN Master Arbitration Loss interrupt Enable. 4 1 read-write DISABLED Disabled. The MstArbLoss interrupt is disabled. 0 ENABLED Enabled. The MstArbLoss interrupt is enabled. 0x1 MSTSTSTPERREN Master Start/Stop Error interrupt Enable. 6 1 read-write DISABLED Disabled. The MstStStpErr interrupt is disabled. 0 ENABLED Enabled. The MstStStpErr interrupt is enabled. 0x1 SLVPENDINGEN Slave Pending interrupt Enable. 8 1 read-write DISABLED Disabled. The SlvPending interrupt is disabled. 0 ENABLED Enabled. The SlvPending interrupt is enabled. 0x1 SLVNOTSTREN Slave Not Stretching interrupt Enable. 11 1 read-write DISABLED Disabled. The SlvNotStr interrupt is disabled. 0 ENABLED Enabled. The SlvNotStr interrupt is enabled. 0x1 SLVDESELEN Slave Deselect interrupt Enable. 15 1 read-write DISABLED Disabled. The SlvDeSel interrupt is disabled. 0 ENABLED Enabled. The SlvDeSel interrupt is enabled. 0x1 MONRDYEN Monitor data Ready interrupt Enable. 16 1 read-write DISABLED Disabled. The MonRdy interrupt is disabled. 0 ENABLED Enabled. The MonRdy interrupt is enabled. 0x1 MONOVEN Monitor Overrun interrupt Enable. 17 1 read-write DISABLED Disabled. The MonOv interrupt is disabled. 0 ENABLED Enabled. The MonOv interrupt is enabled. 0x1 MONIDLEEN Monitor Idle interrupt Enable. 19 1 read-write DISABLED Disabled. The MonIdle interrupt is disabled. 0 ENABLED Enabled. The MonIdle interrupt is enabled. 0x1 EVENTTIMEOUTEN Event time-out interrupt Enable. 24 1 read-write DISABLED Disabled. The Event time-out interrupt is disabled. 0 ENABLED Enabled. The Event time-out interrupt is enabled. 0x1 SCLTIMEOUTEN SCL time-out interrupt Enable. 25 1 read-write DISABLED Disabled. The SCL time-out interrupt is disabled. 0 ENABLED Enabled. The SCL time-out interrupt is enabled. 0x1 INTENCLR Interrupt Enable Clear register. 0xC 32 write-only 0 0 MSTPENDINGCLR Master Pending interrupt clear. Writing 1 to this bit clears the corresponding bit in the INTENSET register if implemented. 0 1 write-only MSTARBLOSSCLR Master Arbitration Loss interrupt clear. 4 1 write-only MSTSTSTPERRCLR Master Start/Stop Error interrupt clear. 6 1 write-only SLVPENDINGCLR Slave Pending interrupt clear. 8 1 write-only SLVNOTSTRCLR Slave Not Stretching interrupt clear. 11 1 write-only SLVDESELCLR Slave Deselect interrupt clear. 15 1 write-only MONRDYCLR Monitor data Ready interrupt clear. 16 1 write-only MONOVCLR Monitor Overrun interrupt clear. 17 1 write-only MONIDLECLR Monitor Idle interrupt clear. 19 1 write-only EVENTTIMEOUTCLR Event time-out interrupt clear. 24 1 write-only SCLTIMEOUTCLR SCL time-out interrupt clear. 25 1 write-only TIMEOUT Time-out value register. 0x10 32 read-write 0xFFFF 0xFFFF TOMIN Time-out time value, bottom four bits. These are hard-wired to 0xF. This gives a minimum time-out of 16 I2C function clocks and also a time-out resolution of 16 I2C function clocks. 0 4 read-write TO Time-out time value. Specifies the time-out interval value in increments of 16 I 2C function clocks, as defined by the CLKDIV register. To change this value while I2C is in operation, disable all time-outs, write a new value to TIMEOUT, then re-enable time-outs. 0x000 = A time-out will occur after 16 counts of the I2C function clock. 0x001 = A time-out will occur after 32 counts of the I2C function clock. 0xFFF = A time-out will occur after 65,536 counts of the I2C function clock. 4 12 read-write CLKDIV Clock pre-divider for the entire I2C interface. This determines what time increments are used for the MSTTIME register, and controls some timing of the Slave function. 0x14 32 read-write 0 0xFFFF DIVVAL This field controls how the Flexcomm clock (FCLK) is used by the I2C functions that need an internal clock in order to operate. 0x0000 = FCLK is used directly by the I2C. 0x0001 = FCLK is divided by 2 before use. 0x0002 = FCLK is divided by 3 before use. 0xFFFF = FCLK is divided by 65,536 before use. 0 16 read-write INTSTAT Interrupt Status register for Master, Slave, and Monitor functions. 0x18 32 read-only 0x801 0x30FFF5F MSTPENDING Master Pending. 0 1 read-only MSTARBLOSS Master Arbitration Loss flag. 4 1 read-only MSTSTSTPERR Master Start/Stop Error flag. 6 1 read-only SLVPENDING Slave Pending. 8 1 read-only SLVNOTSTR Slave Not Stretching status. 11 1 read-only SLVDESEL Slave Deselected flag. 15 1 read-only MONRDY Monitor Ready. 16 1 read-only MONOV Monitor Overflow flag. 17 1 read-only MONIDLE Monitor Idle flag. 19 1 read-only EVENTTIMEOUT Event time-out Interrupt flag. 24 1 read-only SCLTIMEOUT SCL time-out Interrupt flag. 25 1 read-only MSTCTL Master control register. 0x20 32 read-write 0 0xF MSTCONTINUE Master Continue. 0 1 read-write NO_EFFECT No effect. 0 Continue Informs the Master function to continue to the next operation. 0x1 MSTSTART Master Start control. 1 1 read-write NO_EFFECT No effect. 0 START Start. A Start will be generated on the I2C bus at the next allowed time. 0x1 MSTSTOP Master Stop control. 2 1 read-write NO_EFFECT No effect. 0 STOP Stop. A Stop will be generated on the I2C bus at the next allowed time, preceded by a NACK to the slave if the master is receiving data from the slave (Master Receiver mode). 0x1 MSTDMA Master DMA enable. Data operations of the I2C can be performed with DMA. Protocol type operations such as Start, address, Stop, and address match must always be done with software, typically via an interrupt. Address acknowledgement must also be done by software except when the I2C is configured to be HSCAPABLE (and address acknowledgement is handled entirely by hardware) or when Automatic Operation is enabled. When a DMA data transfer is complete, MSTDMA must be cleared prior to beginning the next operation, typically a Start or Stop.This bit is read/write. 3 1 read-write DISABLED Disable. No DMA requests are generated for master operation. 0 ENABLED Enable. A DMA request is generated for I2C master data operations. When this I2C master is generating Acknowledge bits in Master Receiver mode, the acknowledge is generated automatically. 0x1 MSTTIME Master timing configuration. 0x24 32 read-write 0x77 0x77 MSTSCLLOW Master SCL Low time. Specifies the minimum low time that will be asserted by this master on SCL. Other devices on the bus (masters or slaves) could lengthen this time. This corresponds to the parameter t LOW in the I2C bus specification. I2C bus specification parameters tBUF and tSU;STA have the same values and are also controlled by MSTSCLLOW. 0 3 read-write CLOCKS_2 2 clocks. Minimum SCL low time is 2 clocks of the I2C clock pre-divider. 0 CLOCKS_3 3 clocks. Minimum SCL low time is 3 clocks of the I2C clock pre-divider. 0x1 CLOCKS_4 4 clocks. Minimum SCL low time is 4 clocks of the I2C clock pre-divider. 0x2 CLOCKS_5 5 clocks. Minimum SCL low time is 5 clocks of the I2C clock pre-divider. 0x3 CLOCKS_6 6 clocks. Minimum SCL low time is 6 clocks of the I2C clock pre-divider. 0x4 CLOCKS_7 7 clocks. Minimum SCL low time is 7 clocks of the I2C clock pre-divider. 0x5 CLOCKS_8 8 clocks. Minimum SCL low time is 8 clocks of the I2C clock pre-divider. 0x6 CLOCKS_9 9 clocks. Minimum SCL low time is 9 clocks of the I2C clock pre-divider. 0x7 MSTSCLHIGH Master SCL High time. Specifies the minimum high time that will be asserted by this master on SCL. Other masters in a multi-master system could shorten this time. This corresponds to the parameter tHIGH in the I2C bus specification. I2C bus specification parameters tSU;STO and tHD;STA have the same values and are also controlled by MSTSCLHIGH. 4 3 read-write CLOCKS_2 2 clocks. Minimum SCL high time is 2 clock of the I2C clock pre-divider. 0 CLOCKS_3 3 clocks. Minimum SCL high time is 3 clocks of the I2C clock pre-divider . 0x1 CLOCKS_4 4 clocks. Minimum SCL high time is 4 clock of the I2C clock pre-divider. 0x2 CLOCKS_5 5 clocks. Minimum SCL high time is 5 clock of the I2C clock pre-divider. 0x3 CLOCKS_6 6 clocks. Minimum SCL high time is 6 clock of the I2C clock pre-divider. 0x4 CLOCKS_7 7 clocks. Minimum SCL high time is 7 clock of the I2C clock pre-divider. 0x5 CLOCKS_8 8 clocks. Minimum SCL high time is 8 clock of the I2C clock pre-divider. 0x6 CLOCKS_9 9 clocks. Minimum SCL high time is 9 clocks of the I2C clock pre-divider. 0x7 MSTDAT Combined Master receiver and transmitter data register. 0x28 32 read-write 0 0xFF DATA Master function data register. Read: read the most recently received data for the Master function. Write: transmit data using the Master function. 0 8 read-write SLVCTL Slave control register. 0x40 32 read-write 0 0xB SLVCONTINUE Slave Continue. 0 1 read-write NO_EFFECT No effect. 0 Continue Informs the Slave function to continue to the next operation. 0x1 SLVNACK Slave NACK. 1 1 read-write NO_EFFECT No effect. 0 NACK NACK. Causes the Slave function to NACK the master when the slave is receiving data from the master (Slave Receiver mode). 0x1 SLVDMA Slave DMA enable. 3 1 read-write DISABLED Disabled. No DMA requests are issued for Slave mode operation. 0 ENABLED Enabled. DMA requests are issued for I2C slave data transmission and reception. 0x1 SLVDAT Combined Slave receiver and transmitter data register. 0x44 32 read-write 0 0xFF DATA Slave function data register. Read: read the most recently received data for the Slave function. Write: transmit data using the Slave function. 0 8 read-write 4 0x4 SLVADR[%s] Slave address register. 0x48 32 read-write 0x1 0xFF SADISABLE Slave Address n Disable. 0 1 read-write ENABLED Enabled. Slave Address n is enabled. 0 DISABLED Ignored Slave Address n is ignored. 0x1 SLVADR Slave Address. Seven bit slave address that is compared to received addresses if enabled. 1 7 read-write SLVQUAL0 Slave Qualification for address 0. 0x58 32 read-write 0 0xFF QUALMODE0 Qualify mode for slave address 0. 0 1 read-write MASK Mask. The SLVQUAL0 field is used as a logical mask for matching address 0. 0 EXTEND Extend. The SLVQUAL0 field is used to extend address 0 matching in a range of addresses. 0x1 SLVQUAL0 Slave address Qualifier for address 0. A value of 0 causes the address in SLVADR0 to be used as-is, assuming that it is enabled. If QUALMODE0 = 0, any bit in this field which is set to 1 will cause an automatic match of the corresponding bit of the received address when it is compared to the SLVADR0 register. If QUALMODE0 = 1, an address range is matched for address 0. This range extends from the value defined by SLVADR0 to the address defined by SLVQUAL0 (address matches when SLVADR0[7:1] <= received address <= SLVQUAL0[7:1]). 1 7 read-write MONRXDAT Monitor receiver data register. 0x80 32 read-only 0 0x7FF MONRXDAT Monitor function Receiver Data. This reflects every data byte that passes on the I2C pins. 0 8 read-only MONSTART Monitor Received Start. 8 1 read-only NO_START_DETECTED No start detected. The Monitor function has not detected a Start event on the I2C bus. 0 START_DETECTED Start detected. The Monitor function has detected a Start event on the I2C bus. 0x1 MONRESTART Monitor Received Repeated Start. 9 1 read-only NOT_DETECTED No repeated start detected. The Monitor function has not detected a Repeated Start event on the I2C bus. 0 DETECTED Repeated start detected. The Monitor function has detected a Repeated Start event on the I2C bus. 0x1 MONNACK Monitor Received NACK. 10 1 read-only ACKNOWLEDGED Acknowledged. The data currently being provided by the Monitor function was acknowledged by at least one master or slave receiver. 0 NOT_ACKNOWLEDGED Not acknowledged. The data currently being provided by the Monitor function was not acknowledged by any receiver. 0x1 I2C1 LPC82x I2C-bus interfaces I2C 0x40054000 0 0x84 registers I2C1 7 I2C2 LPC82x I2C-bus interfaces I2C 0x40070000 0 0x84 registers I2C2 21 I2C3 LPC82x I2C-bus interfaces I2C 0x40074000 0 0x84 registers I2C3 22 SPI0 LPC82x Serial Peripheral Interfaces (SPI) SPI SPI 0x40058000 0 0x2C registers SPI0 0 CFG SPI Configuration register 0 32 read-write 0 0xFBD ENABLE SPI enable. 0 1 read-write DISABLED Disabled. The SPI is disabled and the internal state machine and counters are reset. 0 ENABLED Enabled. The SPI is enabled for operation. 0x1 MASTER Master mode select. 2 1 read-write SLAVE_MODE Slave mode. The SPI will operate in slave mode. SCK, MOSI, and the SSEL signals are inputs, MISO is an output. 0 MASTER_MODE Master mode. The SPI will operate in master mode. SCK, MOSI, and the SSEL signals are outputs, MISO is an input. 0x1 LSBF LSB First mode enable. 3 1 read-write STANDARD Standard. Data is transmitted and received in standard MSB first order. 0 REVERSE Reverse. Data is transmitted and received in reverse order (LSB first). 0x1 CPHA Clock Phase select. 4 1 read-write CHANGE Change. The SPI captures serial data on the first clock transition of the transfer (when the clock changes away from the rest state). Data is changed on the following edge. 0 CAPTURE Capture. The SPI changes serial data on the first clock transition of the transfer (when the clock changes away from the rest state). Data is captured on the following edge. 0x1 CPOL Clock Polarity select. 5 1 read-write LOW Low. The rest state of the clock (between transfers) is low. 0 HIGH High. The rest state of the clock (between transfers) is high. 0x1 LOOP Loopback mode enable. Loopback mode applies only to Master mode, and connects transmit and receive data connected together to allow simple software testing. 7 1 read-write DISABLED Disabled. 0 ENABLED Enabled. 0x1 SPOL0 SSEL0 Polarity select. 8 1 read-write LOW Low. The SSEL0 pin is active low. 0 HIGH High. The SSEL0 pin is active high. 0x1 SPOL1 SSEL1 Polarity select. 9 1 read-write LOW Low. The SSEL1 pin is active low. 0 HIGH High. The SSEL1 pin is active high. 0x1 SPOL2 SSEL2 Polarity select. 10 1 read-write LOW Low. The SSEL2 pin is active low. 0 HIGH High. The SSEL2 pin is active high. 0x1 SPOL3 SSEL3 Polarity select. 11 1 read-write LOW Low. The SSEL3 pin is active low. 0 HIGH High. The SSEL3 pin is active high. 0x1 DLY SPI Delay register 0x4 32 read-write 0 0xFFFF PRE_DELAY Controls the amount of time between SSEL assertion and the beginning of a data transfer. There is always one SPI clock time between SSEL assertion and the first clock edge. This is not considered part of the pre-delay. 0x0 = No additional time is inserted. 0x1 = 1 SPI clock time is inserted. 0x2 = 2 SPI clock times are inserted. 0xF = 15 SPI clock times are inserted. 0 4 read-write POST_DELAY Controls the amount of time between the end of a data transfer and SSEL deassertion. 0x0 = No additional time is inserted. 0x1 = 1 SPI clock time is inserted. 0x2 = 2 SPI clock times are inserted. 0xF = 15 SPI clock times are inserted. 4 4 read-write FRAME_DELAY If the EOF flag is set, controls the minimum amount of time between the current frame and the next frame (or SSEL deassertion if EOT). 0x0 = No additional time is inserted. 0x1 = 1 SPI clock time is inserted. 0x2 = 2 SPI clock times are inserted. 0xF = 15 SPI clock times are inserted. 8 4 read-write TRANSFER_DELAY Controls the minimum amount of time that the SSEL is deasserted between transfers. 0x0 = The minimum time that SSEL is deasserted is 1 SPI clock time. (Zero added time.) 0x1 = The minimum time that SSEL is deasserted is 2 SPI clock times. 0x2 = The minimum time that SSEL is deasserted is 3 SPI clock times. 0xF = The minimum time that SSEL is deasserted is 16 SPI clock times. 12 4 read-write STAT SPI Status. Some status flags can be cleared by writing a 1 to that bit position 0x8 32 read-write 0x102 0x1FF RXRDY Receiver Ready flag. When 1, indicates that data is available to be read from the receiver buffer. Cleared after a read of the RXDAT register. 0 1 read-only TXRDY Transmitter Ready flag. When 1, this bit indicates that data may be written to the transmit buffer. Previous data may still be in the process of being transmitted. Cleared when data is written to TXDAT or TXDATCTL until the data is moved to the transmit shift register. 1 1 read-only RXOV Receiver Overrun interrupt flag. This flag applies only to slave mode (Master = 0). This flag is set when the beginning of a received character is detected while the receiver buffer is still in use. If this occurs, the receiver buffer contents are preserved, and the incoming data is lost. Data received by the SPI should be considered undefined if RxOv is set. 2 1 write-only TXUR Transmitter Underrun interrupt flag. This flag applies only to slave mode (Master = 0). In this case, the transmitter must begin sending new data on the next input clock if the transmitter is idle. If that data is not available in the transmitter holding register at that point, there is no data to transmit and the TXUR flag is set. Data transmitted by the SPI should be considered undefined if TXUR is set. 3 1 write-only SSA Slave Select Assert. This flag is set whenever any slave select transitions from deasserted to asserted, in both master and slave modes. This allows determining when the SPI transmit/receive functions become busy, and allows waking up the device from reduced power modes when a slave mode access begins. This flag is cleared by software. 4 1 write-only SSD Slave Select Deassert. This flag is set whenever any asserted slave selects transition to deasserted, in both master and slave modes. This allows determining when the SPI transmit/receive functions become idle. This flag is cleared by software. 5 1 write-only STALLED Stalled status flag. This indicates whether the SPI is currently in a stall condition. 6 1 read-only ENDTRANSFER End Transfer control bit. Software can set this bit to force an end to the current transfer when the transmitter finishes any activity already in progress, as if the EOT flag had been set prior to the last transmission. This capability is included to support cases where it is not known when transmit data is written that it will be the end of a transfer. The bit is cleared when the transmitter becomes idle as the transfer comes to an end. Forcing an end of transfer in this manner causes any specified FRAME_DELAY and TRANSFER_DELAY to be inserted. 7 1 read-write MSTIDLE Master idle status flag. This bit is 1 whenever the SPI master function is fully idle. This means that the transmit holding register is empty and the transmitter is not in the process of sending data. 8 1 read-only INTENSET SPI Interrupt Enable read and Set. A complete value may be read from this register. Writing a 1 to any implemented bit position causes that bit to be set. 0xC 32 read-write 0 0x13F RXRDYEN Determines whether an interrupt occurs when receiver data is available. 0 1 read-write RXRDYEN_0 No interrupt will be generated when receiver data is available. 0 RXRDYEN_1 An interrupt will be generated when receiver data is available in the RXDAT register. 0x1 TXRDYEN Determines whether an interrupt occurs when the transmitter holding register is available. 1 1 read-write TXRDYEN_0 No interrupt will be generated when the transmitter holding register is available. 0 TXRDYEN_1 An interrupt will be generated when data may be written to TXDAT. 0x1 RXOVEN Determines whether an interrupt occurs when a receiver overrun occurs. This happens in slave mode when there is a need for the receiver to move newly received data to the RXDAT register when it is already in use. The interface prevents receiver overrun in Master mode by not allowing a new transmission to begin when a receiver overrun would otherwise occur. 2 1 read-write RXOVEN_0 No interrupt will be generated when a receiver overrun occurs. 0 RXOVEN_1 An interrupt will be generated if a receiver overrun occurs. 0x1 TXUREN Determines whether an interrupt occurs when a transmitter underrun occurs. This happens in slave mode when there is a need to transmit data when none is available. 3 1 read-write TXUREN_0 No interrupt will be generated when the transmitter underruns. 0 TXUREN_1 An interrupt will be generated if the transmitter underruns. 0x1 SSAEN Determines whether an interrupt occurs when the Slave Select is asserted. 4 1 read-write SSAEN_0 No interrupt will be generated when any Slave Select transitions from deasserted to asserted. 0 SSAEN_1 An interrupt will be generated when any Slave Select transitions from deasserted to asserted. 0x1 SSDEN Determines whether an interrupt occurs when the Slave Select is deasserted. 5 1 read-write SSDEN_0 No interrupt will be generated when all asserted Slave Selects transition to deasserted. 0 SSDEN_1 An interrupt will be generated when all asserted Slave Selects transition to deasserted. 0x1 MSTIDLEEN Determines whether an interrupt occurs when the MSTIDLE enable 8 1 read-write MSTIDLEEN_0 No interrupt will be generated when MSTIDLE enabled. 0 MSTIDLEEN_1 An interrupt will be generated when MSTIDLE enabled. 0x1 INTENCLR SPI Interrupt Enable Clear. Writing a 1 to any implemented bit position causes the corresponding bit in INTENSET to be cleared. 0x10 32 write-only 0 0 RXRDYEN Writing 1 clears the corresponding bits in the INTENSET register. 0 1 write-only TXRDYEN Writing 1 clears the corresponding bits in the INTENSET register. 1 1 write-only RXOVEN Writing 1 clears the corresponding bits in the INTENSET register. 2 1 write-only TXUREN Writing 1 clears the corresponding bits in the INTENSET register. 3 1 write-only SSAEN Writing 1 clears the corresponding bits in the INTENSET register. 4 1 write-only SSDEN Writing 1 clears the corresponding bits in the INTENSET register. 5 1 write-only MSTIDLE Writing 1 clears the corresponding bits in the INTENSET register. 8 1 write-only RXDAT SPI Receive Data 0x14 32 read-only 0 0 RXDAT Receiver Data. This contains the next piece of received data. The number of bits that are used depends on the LEN setting in TXCTL / TXDATCTL. 0 16 read-only RXSSEL0_N Slave Select for receive. This field allows the state of the SSEL0 pin to be saved along with received data. The value will reflect the SSEL0 pin for both master and slave operation. A zero indicates that a slave select is active. The actual polarity of each slave select pin is configured by the related SPOL bit in CFG. 16 1 read-only RXSSEL1_N Slave Select for receive. This field allows the state of the SSEL1 pin to be saved along with received data. The value will reflect the SSEL1 pin for both master and slave operation. A zero indicates that a slave select is active. The actual polarity of each slave select pin is configured by the related SPOL bit in CFG. 17 1 read-only RXSSEL2_N Slave Select for receive. This field allows the state of the SSEL2 pin to be saved along with received data. The value will reflect the SSEL2 pin for both master and slave operation. A zero indicates that a slave select is active. The actual polarity of each slave select pin is configured by the related SPOL bit in CFG. 18 1 read-only RXSSEL3_N Slave Select for receive. This field allows the state of the SSEL3 pin to be saved along with received data. The value will reflect the SSEL3 pin for both master and slave operation. A zero indicates that a slave select is active. The actual polarity of each slave select pin is configured by the related SPOL bit in CFG. 19 1 read-only SOT Start of Transfer flag. This flag will be 1 if this is the first data after the SSELs went from deasserted to asserted (i.e., any previous transfer has ended). This information can be used to identify the first piece of data in cases where the transfer length is greater than 16 bit. 20 1 read-only TXDATCTL SPI Transmit Data with Control 0x18 32 read-write 0 0xF7FFFFF TXDAT Transmit Data. This field provides from 1 to 16 bits of data to be transmitted. 0 16 read-write TXSSEL0_N Transmit Slave Select. This field asserts SSEL0 in master mode. The output on the pin is active LOW by default. Remark: The active state of the SSEL0 pin is configured by bits in the CFG register. 16 1 read-write TXSSEL0_N_0 SSEL0 asserted. 0 TXSSEL0_N_1 SSEL0 not asserted. 0x1 TXSSEL1_N Transmit Slave Select. This field asserts SSEL1 in master mode. The output on the pin is active LOW by default. Remark: The active state of the SSEL1 pin is configured by bits in the CFG register. 17 1 read-write TXSSEL1_N_0 SSEL1 asserted. 0 TXSSEL1_N_1 SSEL1 not asserted. 0x1 TXSSEL2_N Transmit Slave Select. This field asserts SSEL2 in master mode. The output on the pin is active LOW by default. Remark: The active state of the SSEL2 pin is configured by bits in the CFG register. 18 1 read-write TXSSEL2_N_0 SSEL2 asserted. 0 TXSSEL2_N_1 SSEL2 not asserted. 0x1 TXSSEL3_N Transmit Slave Select. This field asserts SSEL3 in master mode. The output on the pin is active LOW by default. Remark: The active state of the SSEL3 pin is configured by bits in the CFG register. 19 1 read-write TXSSEL3_N_0 SSEL3 asserted. 0 TXSSEL3_N_1 SSEL3 not asserted. 0x1 EOT End of Transfer. The asserted SSEL will be deasserted at the end of a transfer, and remain so for at least the time specified by the Transfer_delay value in the DLY register. 20 1 read-write SSEL_deasserted This piece of data is not treated as the end of a transfer. SSEL will not be deasserted at the end of this data. 0 SSEL_not_deasserted This piece of data is treated as the end of a transfer. SSEL will be deasserted at the end of this piece of data. 0x1 EOF End of Frame. Between frames, a delay may be inserted, as defined by the FRAME_DELAY value in the DLY register. The end of a frame may not be particularly meaningful if the FRAME_DELAY value = 0. This control can be used as part of the support for frame lengths greater than 16 bits. 21 1 read-write Data_not_EOF This piece of data transmitted is not treated as the end of a frame. 0 Data_EOF This piece of data is treated as the end of a frame, causing the FRAME_DELAY time to be inserted before subsequent data is transmitted. 0x1 RXIGNORE Receive Ignore. This allows data to be transmitted using the SPI without the need to read unneeded data from the receiver.Setting this bit simplifies the transmit process and can be used with the DMA. 22 1 read-write Read_received_data Received data must be read in order to allow transmission to progress. In slave mode, an overrun error will occur if received data is not read before new data is received. 0 Ignore_received_data Received data is ignored, allowing transmission without reading unneeded received data. No receiver flags are generated. 0x1 LEN Data Length. Specifies the data length from 1 to 16 bits. Note that transfer lengths greater than 16 bits are supported by implementing multiple sequential transmits. 0x0 = Data transfer is 1 bit in length. 0x1 = Data transfer is 2 bits in length. 0x2 = Data transfer is 3 bits in length. ... 0xF = Data transfer is 16 bits in length. 24 4 read-write LEN_0 no description available 0 LEN_1 Data transfer is 1 bit in length. 0x1 LEN_2 Data transfer is 2 bit in length. 0x2 LEN_3 Data transfer is 3 bit in length. 0x3 LEN_4 Data transfer is 4 bit in length. 0x4 LEN_5 Data transfer is 5 bit in length. 0x5 LEN_6 Data transfer is 6 bit in length. 0x6 LEN_7 Data transfer is 7 bit in length. 0x7 LEN_8 Data transfer is 8 bit in length. 0x8 LEN_9 Data transfer is 9 bit in length. 0x9 LEN_10 Data transfer is 10 bit in length. 0xA LEN_11 Data transfer is 11 bit in length. 0xB LEN_12 Data transfer is 12 bit in length. 0xC LEN_13 Data transfer is 13 bit in length. 0xD LEN_14 Data transfer is 14 bit in length. 0xE LEN_15 Data transfer is 15 bit in length. 0xF TXDAT SPI Transmit Data. 0x1C 32 read-write 0 0xFFFF DATA Transmit Data. This field provides from 4 to 16 bits of data to be transmitted. 0 16 read-write TXCTL SPI Transmit Control 0x20 32 read-write 0 0xF7F0000 TXSSEL0_N Transmit Slave Select 0. 16 1 read-write TXSSEL1_N Transmit Slave Select 1. 17 1 read-write TXSSEL2_N Transmit Slave Select 2. 18 1 read-write TXSSEL3_N Transmit Slave Select 3. 19 1 read-write EOT End of Transfer. 20 1 read-write EOF End of Frame. 21 1 read-write RXIGNORE Receive Ignore. 22 1 read-write LEN Data transfer Length. 24 4 read-write DIV SPI clock Divider 0x24 32 read-write 0 0xFFFF DIVVAL Rate divider value. Specifies how the Flexcomm clock (FCLK) is divided to produce the SPI clock rate in master mode. DIVVAL is -1 encoded such that the value 0 results in FCLK/1, the value 1 results in FCLK/2, up to the maximum possible divide value of 0xFFFF, which results in FCLK/65536. 0 16 read-write INTSTAT SPI Interrupt Status 0x28 32 read-write 0x2 0x1FF RXRDY Receiver Ready flag. 0 1 read-only TXRDY Transmitter Ready flag. 1 1 read-only RXOV Receiver Overrun interrupt flag. 2 1 read-only TXUR Transmitter Underrun interrupt flag. 3 1 read-only SSA Slave Select Assert. 4 1 read-only SSD Slave Select Deassert. 5 1 read-only MSTIDLE Master Idle status flag. 8 1 read-only SPI1 LPC82x Serial Peripheral Interfaces (SPI) SPI 0x4005C000 0 0x2C registers SPI1 1 USART0 LPC82x USARTs USART USART 0x40064000 0 0x30 registers USART0 3 CFG USART Configuration register. Basic USART configuration settings that typically are not changed during operation. 0 32 read-write 0 0xFDDBFD ENABLE USART Enable. 0 1 read-write DISABLED Disabled. The USART is disabled and the internal state machine and counters are reset. While Enable = 0, all USART interrupts and DMA transfers are disabled. When Enable is set again, CFG and most other control bits remain unchanged. When re-enabled, the USART will immediately be ready to transmit because the transmitter has been reset and is therefore available. 0 ENABLED Enabled. The USART is enabled for operation. 0x1 DATALEN Selects the data size for the USART. 2 2 read-write BIT_7 7 bit Data length. 0 BIT_8 8 bit Data length. 0x1 BIT_9 9 bit data length. The 9th bit is commonly used for addressing in multidrop mode. See the ADDRDET bit in the CTL register. 0x2 PARITYSEL Selects what type of parity is used by the USART. 4 2 read-write NO_PARITY No parity. 0 EVEN_PARITY Even parity. Adds a bit to each character such that the number of 1s in a transmitted character is even, and the number of 1s in a received character is expected to be even. 0x2 ODD_PARITY Odd parity. Adds a bit to each character such that the number of 1s in a transmitted character is odd, and the number of 1s in a received character is expected to be odd. 0x3 STOPLEN Number of stop bits appended to transmitted data. Only a single stop bit is required for received data. 6 1 read-write BIT_1 1 stop bit. 0 BITS_2 2 stop bits. This setting should only be used for asynchronous communication. 0x1 CTSEN CTS Enable. Determines whether CTS is used for flow control. CTS can be from the input pin, or from the USART's own RTS if loopback mode is enabled. 9 1 read-write DISABLED No flow control. The transmitter does not receive any automatic flow control signal. 0 ENABLED Flow control enabled. The transmitter uses the CTS input (or RTS output in loopback mode) for flow control purposes. 0x1 SYNCEN Selects synchronous or asynchronous operation. 11 1 read-write ASYNCHRONOUS_MODE Asynchronous mode. 0 SYNCHRONOUS_MODE Synchronous mode. 0x1 CLKPOL Selects the clock polarity and sampling edge of received data in synchronous mode. 12 1 read-write FALLING_EDGE Falling edge. Un_RXD is sampled on the falling edge of SCLK. 0 RISING_EDGE Rising edge. Un_RXD is sampled on the rising edge of SCLK. 0x1 SYNCMST Synchronous mode Master select. 14 1 read-write SLAVE Slave. When synchronous mode is enabled, the USART is a slave. 0 MASTER Master. When synchronous mode is enabled, the USART is a master. 0x1 LOOP Selects data loopback mode. 15 1 read-write NORMAL Normal operation. 0 LOOPBACK Loopback mode. This provides a mechanism to perform diagnostic loopback testing for USART data. Serial data from the transmitter (Un_TXD) is connected internally to serial input of the receive (Un_RXD). Un_TXD and Un_RTS activity will also appear on external pins if these functions are configured to appear on device pins. The receiver RTS signal is also looped back to CTS and performs flow control if enabled by CTSEN. 0x1 OETA Output Enable Turnaround time enable for RS-485 operation. 18 1 read-write DISABLED Disabled. If selected by OESEL, the Output Enable signal deasserted at the end of the last stop bit of a transmission. 0 ENABLED Enabled. If selected by OESEL, the Output Enable signal remains asserted for one character time after the end of the last stop bit of a transmission. OE will also remain asserted if another transmit begins before it is deasserted. 0x1 AUTOADDR Automatic Address matching enable. 19 1 read-write DISABLED Disabled. When addressing is enabled by ADDRDET, address matching is done by software. This provides the possibility of versatile addressing (e.g. respond to more than one address). 0 ENABLED Enabled. When addressing is enabled by ADDRDET, address matching is done by hardware, using the value in the ADDR register as the address to match. 0x1 OESEL Output Enable Select. 20 1 read-write STANDARD Standard. The RTS signal is used as the standard flow control function. 0 RS_485 RS-485. The RTS signal configured to provide an output enable signal to control an RS-485 transceiver. 0x1 OEPOL Output Enable Polarity. 21 1 read-write LOW Low. If selected by OESEL, the output enable is active low. 0 HIGH High. If selected by OESEL, the output enable is active high. 0x1 RXPOL Receive data polarity. 22 1 read-write STANDARD Standard. The RX signal is used as it arrives from the pin. This means that the RX rest value is 1, start bit is 0, data is not inverted, and the stop bit is 1. 0 INVERTED Inverted. The RX signal is inverted before being used by the USART. This means that the RX rest value is 0, start bit is 1, data is inverted, and the stop bit is 0. 0x1 TXPOL Transmit data polarity. 23 1 read-write STANDARD Standard. The TX signal is sent out without change. This means that the TX rest value is 1, start bit is 0, data is not inverted, and the stop bit is 1. 0 INVERTED Inverted. The TX signal is inverted by the USART before being sent out. This means that the TX rest value is 0, start bit is 1, data is inverted, and the stop bit is 0. 0x1 CTL USART Control register. USART control settings that are more likely to change during operation. 0x4 32 read-write 0 0x10346 TXBRKEN Break Enable. 1 1 read-write NORMAL Normal operation. 0 CONTINOUS Continuous break. Continuous break is sent immediately when this bit is set, and remains until this bit is cleared. A break may be sent without danger of corrupting any currently transmitting character if the transmitter is first disabled (TXDIS in CTL is set) and then waiting for the transmitter to be disabled (TXDISINT in STAT = 1) before writing 1 to TXBRKEN. 0x1 ADDRDET Enable address detect mode. 2 1 read-write DISABLED Disabled. The USART presents all incoming data. 0 ENABLED Enabled. The USART receiver ignores incoming data that does not have the most significant bit of the data (typically the 9th bit) = 1. When the data MSB bit = 1, the receiver treats the incoming data normally, generating a received data interrupt. Software can then check the data to see if this is an address that should be handled. If it is, the ADDRDET bit is cleared by software and further incoming data is handled normally. 0x1 TXDIS Transmit Disable. 6 1 read-write ENABLED Not disabled. USART transmitter is not disabled. 0 DISABLED Disabled. USART transmitter is disabled after any character currently being transmitted is complete. This feature can be used to facilitate software flow control. 0x1 CC Continuous Clock generation. By default, SCLK is only output while data is being transmitted in synchronous mode. 8 1 read-write CLOCK_ON_CHARACTER Clock on character. In synchronous mode, SCLK cycles only when characters are being sent on Un_TXD or to complete a character that is being received. 0 CONTINOUS_CLOCK Continuous clock. SCLK runs continuously in synchronous mode, allowing characters to be received on Un_RxD independently from transmission on Un_TXD). 0x1 CLRCCONRX Clear Continuous Clock. 9 1 read-write NO_EFFECT No effect. No effect on the CC bit. 0 AUTO_CLEAR Auto-clear. The CC bit is automatically cleared when a complete character has been received. This bit is cleared at the same time. 0x1 AUTOBAUD Autobaud enable. 16 1 read-write DISABLED Disabled. USART is in normal operating mode. 0 ENABLED Enabled. USART is in autobaud mode. This bit should only be set when the USART receiver is idle. The first start bit of RX is measured and used the update the BRG register to match the received data rate. AUTOBAUD is cleared once this process is complete, or if there is an AERR. 0x1 STAT USART Status register. The complete status value can be read here. Writing ones clears some bits in the register. Some bits can be cleared by writing a 1 to them. 0x8 32 read-write 0xE 0x1FD7F RXRDY Receiver Ready flag. When 1, indicates that data is available to be read from the receiver buffer. Cleared after a read of the RXDAT or RXDATSTAT registers. 0 1 read-only RXIDLE Receiver Idle. When 0, indicates that the receiver is currently in the process of receiving data. When 1, indicates that the receiver is not currently in the process of receiving data. 1 1 read-only TXRDY Transmitter Ready flag. When 1, this bit indicates that data may be written to the transmit buffer. Previous data may still be in the process of being transmitted. Cleared when data is written to TXDAT. Set when the data is moved from the transmit buffer to the transmit shift register. 2 1 read-only TXIDLE Transmitter Idle. When 0, indicates that the transmitter is currently in the process of sending data.When 1, indicate that the transmitter is not currently in the process of sending data. 3 1 read-only CTS This bit reflects the current state of the CTS signal, regardless of the setting of the CTSEN bit in the CFG register. This will be the value of the CTS input pin unless loopback mode is enabled. 4 1 read-only DELTACTS This bit is set when a change in the state is detected for the CTS flag above. This bit is cleared by software. 5 1 TXDISSTAT Transmitter Disabled Interrupt flag. When 1, this bit indicates that the USART transmitter is fully idle after being disabled via the TXDIS in the CTL register (TXDIS = 1). 6 1 read-only OVERRUNINT Overrun Error interrupt flag. This flag is set when a new character is received while the receiver buffer is still in use. If this occurs, the newly received character in the shift register is lost. 8 1 RXBRK Received Break. This bit reflects the current state of the receiver break detection logic. It is set when the Un_RXD pin remains low for 16 bit times. Note that FRAMERRINT will also be set when this condition occurs because the stop bit(s) for the character would be missing. RXBRK is cleared when the Un_RXD pin goes high. 10 1 read-only DELTARXBRK This bit is set when a change in the state of receiver break detection occurs.Cleared by software. 11 1 START This bit is set when a start is detected on the receiver input. Its purpose is primarily to allow wake-up from Deep-sleep or Power-down mode immediately when a start is detected. Cleared by software. 12 1 FRAMERRINT Framing Error interrupt flag. This flag is set when a character is received with a missing stop bit at the expected location. This could be an indication of a baud rate or configuration mismatch with the transmitting source. 13 1 PARITYERRINT Parity Error interrupt flag. This flag is set when a parity error is detected in a received character. 14 1 RXNOISEINT Received Noise interrupt flag. Three samples of received data are taken in order to determine the value of each received data bit, except in synchronous mode. This acts as a noise filter if one sample disagrees. This flag is set when a received data bit contains one disagreeing sample. This could indicate line noise, a baud rate or character format mismatch, or loss of synchronization during data reception. 15 1 ABERR Autobaud Error. An autobaud error can occur if the BRG counts to its limit before the end of the start bit that is being measured, essentially an autobaud time-out. 16 1 INTENSET Interrupt Enable read and Set register. Contains an individual interrupt enable bit for each potential USART interrupt. A complete value may be read from this register. Writing a 1 to any implemented bit position causes that bit to be set. 0xC 32 read-write 0 0x1F96D RXRDYEN When 1, enables an interrupt when there is a received character available to be read from the RXDAT register. 0 1 read-write TXRDYEN When 1, enables an interrupt when the TXDAT register is available to take another character to transmit. 2 1 read-write TXIDLEEN When 1, enables an interrupt when the transmitter becomes idle (TXIDLE = 1). 3 1 read-write DELTACTSEN When 1, enables an interrupt when there is a change in the state of the CTS input. 5 1 read-write TXDISEN When 1, enables an interrupt when the transmitter is fully disabled as indicated by the TXDISINT flag in STAT. See description of the TXDISINT bit for details. 6 1 read-write OVERRUNEN When 1, enables an interrupt when an overrun error occurred. 8 1 read-write DELTARXBRKEN When 1, enables an interrupt when a change of state has occurred in the detection of a received break condition (break condition asserted or deasserted). 11 1 read-write STARTEN When 1, enables an interrupt when a received start bit has been detected. 12 1 read-write FRAMERREN When 1, enables an interrupt when a framing error has been detected. 13 1 read-write PARITYERREN When 1, enables an interrupt when a parity error has been detected. 14 1 read-write RXNOISEEN When 1, enables an interrupt when noise is detected. 15 1 read-write ABERREN When 1, enables an interrupt when an autobaud error occurs. 16 1 read-write INTENCLR Interrupt Enable Clear register. Allows clearing any combination of bits in the INTENSET register. Writing a 1 to any implemented bit position causes the corresponding bit to be cleared. 0x10 32 write-only 0 0 RXRDYCLR Writing 1 clears the corresponding bit in the INTENSET register. 0 1 write-only TXRDYCLR Writing 1 clears the corresponding bit in the INTENSET register. 2 1 write-only TXIDLECLR Writing 1 clears the corresponding bit in the INTENSET register. 3 1 write-only DELTACTSCLR Writing 1 clears the corresponding bit in the INTENSET register. 5 1 write-only TXDISINTCLR Writing 1 clears the corresponding bit in the INTENSET register. 6 1 write-only OVERRUNCLR Writing 1 clears the corresponding bit in the INTENSET register. 8 1 write-only DELTARXBRKCLR Writing 1 clears the corresponding bit in the INTENSET register. 11 1 write-only STARTCLR Writing 1 clears the corresponding bit in the INTENSET register. 12 1 write-only FRAMERRCLR Writing 1 clears the corresponding bit in the INTENSET register. 13 1 write-only PARITYERRCLR Writing 1 clears the corresponding bit in the INTENSET register. 14 1 write-only RXNOISECLR Writing 1 clears the corresponding bit in the INTENSET register. 15 1 write-only ABERRCLR Writing 1 clears the corresponding bit in the INTENSET register. 16 1 write-only RXDAT Receiver Data register. Contains the last character received. 0x14 32 read-only 0 0 RXDAT The USART Receiver Data register contains the next received character. The number of bits that are relevant depends on the USART configuration settings. 0 9 read-only RXDATSTAT Receiver Data with Status register. Combines the last character received with the current USART receive status. Allows DMA or software to recover incoming data and status together. 0x18 32 read-only 0 0 RXDAT The USART Receiver Data register contains the next received character. The number of bits that are relevant depends on the USART configuration settings. 0 9 read-only FRAMERR Framing Error status flag. This bit is valid when there is a character to be read in the RXDAT register and reflects the status of that character. This bit will set when the character in RXDAT was received with a missing stop bit at the expected location. This could be an indication of a baud rate or configuration mismatch with the transmitting source. 13 1 read-only PARITYERR Parity Error status flag. This bit is valid when there is a character to be read in the RXDAT register and reflects the status of that character. This bit will be set when a parity error is detected in a received character. 14 1 read-only RXNOISE Received Noise flag. 15 1 read-only TXDAT Transmit Data register. Data to be transmitted is written here. 0x1C 32 read-write 0 0x1FF TXDAT Writing to the USART Transmit Data Register causes the data to be transmitted as soon as the transmit shift register is available and any conditions for transmitting data are met: CTS low (if CTSEN bit = 1), TXDIS bit = 0. 0 9 read-write BRG Baud Rate Generator register. 16-bit integer baud rate divisor value. 0x20 32 read-write 0 0xFFFF BRGVAL This value is used to divide the USART input clock to determine the baud rate, based on the input clock from the FRG. 0 = FCLK is used directly by the USART function. 1 = FCLK is divided by 2 before use by the USART function. 2 = FCLK is divided by 3 before use by the USART function. 0xFFFF = FCLK is divided by 65,536 before use by the USART function. 0 16 read-write INTSTAT Interrupt status register. Reflects interrupts that are currently enabled. 0x24 32 read-write 0x5 0x1FD7F RXRDY Receiver Ready flag. 0 1 read-only TXRDY Transmitter Ready flag. 2 1 read-only TXIDLE Transmitter idle status. 3 1 read-only DELTACTS This bit is set when a change in the state of the CTS input is detected. 5 1 read-only TXDISINT Transmitter Disabled Interrupt flag. 6 1 read-only OVERRUNINT Overrun Error interrupt flag. 8 1 read-only DELTARXBRK This bit is set when a change in the state of receiver break detection occurs. 11 1 read-only START This bit is set when a start is detected on the receiver input. 12 1 read-only FRAMERRINT Framing Error interrupt flag. 13 1 read-only PARITYERRINT Parity Error interrupt flag. 14 1 read-only RXNOISEINT Received Noise interrupt flag. 15 1 read-only ABERR Autobaud Error flag. 16 1 read-only OSR Oversample selection register for asynchronous communication. 0x28 32 read-write 0xF 0xF OSRVAL Oversample Selection Value. 0 to 3 = not supported 0x4 = 5 function clocks are used to transmit and receive each data bit. 0x5 = 6 function clocks are used to transmit and receive each data bit. 0xF= 16 function clocks are used to transmit and receive each data bit. 0 4 read-write ADDR Address register for automatic address matching. 0x2C 32 read-write 0 0xFF ADDRESS 8-bit address used with automatic address matching. Used when address detection is enabled (ADDRDET in CTL = 1) and automatic address matching is enabled (AUTOADDR in CFG = 1). 0 8 read-write USART1 LPC82x USARTs USART 0x40068000 0 0x30 registers USART1 4 USART2 LPC82x USARTs USART 0x4006C000 0 0x30 registers USART2 5 CRC LPC5411x CRC engine CRC 0x50000000 0 0xC registers MODE CRC mode register 0 32 read-write 0 0x3F CRC_POLY CRC polynomial: 1X = CRC-32 polynomial 01 = CRC-16 polynomial 00 = CRC-CCITT polynomial 0 2 read-write BIT_RVS_WR Data bit order: 1 = Bit order reverse for CRC_WR_DATA (per byte) 0 = No bit order reverse for CRC_WR_DATA (per byte) 2 1 read-write CMPL_WR Data complement: 1 = 1's complement for CRC_WR_DATA 0 = No 1's complement for CRC_WR_DATA 3 1 read-write BIT_RVS_SUM CRC sum bit order: 1 = Bit order reverse for CRC_SUM 0 = No bit order reverse for CRC_SUM 4 1 read-write CMPL_SUM CRC sum complement: 1 = 1's complement for CRC_SUM 0 = No 1's complement for CRC_SUM 5 1 read-write SEED CRC seed register 0x4 32 read-write 0xFFFF 0xFFFFFFFF CRC_SEED A write access to this register will load CRC seed value to CRC_SUM register with selected bit order and 1's complement pre-processes. A write access to this register will overrule the CRC calculation in progresses. 0 32 read-write SUM CRC checksum register SUM_WR_DATA 0x8 32 read-only 0xFFFF 0xFFFFFFFF CRC_SUM The most recent CRC sum can be read through this register with selected bit order and 1's complement post-processes. 0 32 read-only WR_DATA CRC data register SUM_WR_DATA 0x8 32 write-only 0 0 CRC_WR_DATA Data written to this register will be taken to perform CRC calculation with selected bit order and 1's complement pre-process. Any write size 8, 16 or 32-bit are allowed and accept back-to-back transactions. 0 32 write-only SCT0 LPC82x SCTimer/PWM (SCT) SCT 0x50004000 0 0x530 registers SCT0 9 CONFIG SCT configuration register 0 32 read-write 0x1E00 0x61FFF UNIFY SCT operation 0 1 read-write DUAL_COUNTER The SCT operates as two 16-bit counters named COUNTER_L and COUNTER_H. 0 UNIFIED_COUNTER The SCT operates as a unified 32-bit counter. 0x1 CLKMODE SCT clock mode 1 2 read-write SYSTEM_CLOCK_MODE System Clock Mode. The system clock clocks the entire SCT module including the counter(s) and counter prescalers. 0 SAMPLED_SYSTEM_CLOCK_MODE Sampled System Clock Mode. The system clock clocks the SCT module, but the counter and prescalers are only enabled to count when the designated edge is detected on the input selected by the CKSEL field. The minimum pulse width on the selected clock-gate input is 1 bus clock period. This mode is the high-performance, sampled-clock mode. 0x1 SCT_INPUT_CLOCK_MODE SCT Input Clock Mode. The input/edge selected by the CKSEL field clocks the SCT module, including the counters and prescalers, after first being synchronized to the system clock. The minimum pulse width on the clock input is 1 bus clock period. This mode is the low-power, sampled-clock mode. 0x2 ASYNCHRONOUS_MODE Asynchronous Mode. The entire SCT module is clocked directly by the input/edge selected by the CKSEL field. In this mode, the SCT outputs are switched synchronously to the SCT input clock - not the system clock. The input clock rate must be at least half the system clock rate and can be the same or faster than the system clock. 0x3 CKSEL SCT clock select. The specific functionality of the designated input/edge is dependent on the CLKMODE bit selection in this register. 3 4 read-write INPUT_0_RISING_EDGES Rising edges on input 0. 0 INPUT_0_FALLING_EDGE Falling edges on input 0. 0x1 INPUT_1_RISING_EDGES Rising edges on input 1. 0x2 INPUT_1_FALLING_EDGE Falling edges on input 1. 0x3 INPUT_2_RISING_EDGES Rising edges on input 2. 0x4 INPUT_2_FALLING_EDGE Falling edges on input 2. 0x5 INPUT_3_RISING_EDGES Rising edges on input 3. 0x6 INPUT_3_FALLING_EDGE Falling edges on input 3. 0x7 NORELAOD_L A 1 in this bit prevents the lower match registers from being reloaded from their respective reload registers. Setting this bit eliminates the need to write to the reload registers MATCHREL if the match values are fixed. Software can write to set or clear this bit at any time. This bit applies to both the higher and lower registers when the UNIFY bit is set. 7 1 read-write NORELOAD_H A 1 in this bit prevents the higher match registers from being reloaded from their respective reload registers. Setting this bit eliminates the need to write to the reload registers MATCHREL if the match values are fixed. Software can write to set or clear this bit at any time. This bit is not used when the UNIFY bit is set. 8 1 read-write INSYNC Synchronization for input N (bit 9 = input 0, bit 10 = input 1,, bit 12 = input 3); all other bits are reserved. A 1 in one of these bits subjects the corresponding input to synchronization to the SCT clock, before it is used to create an event. If an input is known to already be synchronous to the SCT clock, this bit may be set to 0 for faster input response. (Note: The SCT clock is the system clock for CKMODEs 0-2. It is the selected, asynchronous SCT input clock for CKMODE3). Note that the INSYNC field only affects inputs used for event generation. It does not apply to the clock input specified in the CKSEL field. 9 4 read-write AUTOLIMIT_L A one in this bit causes a match on match register 0 to be treated as a de-facto LIMIT condition without the need to define an associated event. As with any LIMIT event, this automatic limit causes the counter to be cleared to zero in unidirectional mode or to change the direction of count in bi-directional mode. Software can write to set or clear this bit at any time. This bit applies to both the higher and lower registers when the UNIFY bit is set. 17 1 read-write AUTOLIMIT_H A one in this bit will cause a match on match register 0 to be treated as a de-facto LIMIT condition without the need to define an associated event. As with any LIMIT event, this automatic limit causes the counter to be cleared to zero in unidirectional mode or to change the direction of count in bi-directional mode. Software can write to set or clear this bit at any time. This bit is not used when the UNIFY bit is set. 18 1 read-write CTRL SCT control register 0x4 32 read-write 0x40004 0x1FFF1FFF DOWN_L This bit is 1 when the L or unified counter is counting down. Hardware sets this bit when the counter is counting up, counter limit occurs, and BIDIR = 1.Hardware clears this bit when the counter is counting down and a limit condition occurs or when the counter reaches 0. 0 1 read-write STOP_L When this bit is 1 and HALT is 0, the L or unified counter does not run, but I/O events related to the counter can occur. If a designated start event occurs, this bit is cleared and counting resumes. 1 1 read-write HALT_L When this bit is 1, the L or unified counter does not run and no events can occur. A reset sets this bit. When the HALT_L bit is one, the STOP_L bit is cleared. It is possible to remove the halt condition while keeping the SCT in the stop condition (not running) with a single write to this register to simultaneously clear the HALT bit and set the STOP bit. Once set, only software can clear this bit to restore counter operation. This bit is set on reset. 2 1 read-write CLRCTR_L Writing a 1 to this bit clears the L or unified counter. This bit always reads as 0. 3 1 read-write BIDIR_L L or unified counter direction select 4 1 read-write UP Up. The counter counts up to a limit condition, then is cleared to zero. 0 UP_DOWN Up-down. The counter counts up to a limit, then counts down to a limit condition or to 0. 0x1 PRE_L Specifies the factor by which the SCT clock is prescaled to produce the L or unified counter clock. The counter clock is clocked at the rate of the SCT clock divided by PRE_L+1. Clear the counter (by writing a 1 to the CLRCTR bit) whenever changing the PRE value. 5 8 read-write DOWN_H This bit is 1 when the H counter is counting down. Hardware sets this bit when the counter is counting, a counter limit condition occurs, and BIDIR is 1. Hardware clears this bit when the counter is counting down and a limit condition occurs or when the counter reaches 0. 16 1 read-write STOP_H When this bit is 1 and HALT is 0, the H counter does not, run but I/O events related to the counter can occur. If such an event matches the mask in the Start register, this bit is cleared and counting resumes. 17 1 read-write HALT_H When this bit is 1, the H counter does not run and no events can occur. A reset sets this bit. When the HALT_H bit is one, the STOP_H bit is cleared. It is possible to remove the halt condition while keeping the SCT in the stop condition (not running) with a single write to this register to simultaneously clear the HALT bit and set the STOP bit. Once set, this bit can only be cleared by software to restore counter operation. This bit is set on reset. 18 1 read-write CLRCTR_H Writing a 1 to this bit clears the H counter. This bit always reads as 0. 19 1 read-write BIDIR_H Direction select 20 1 read-write UP The H counter counts up to its limit condition, then is cleared to zero. 0 UP_DOWN The H counter counts up to its limit, then counts down to a limit condition or to 0. 0x1 PRE_H Specifies the factor by which the SCT clock is prescaled to produce the H counter clock. The counter clock is clocked at the rate of the SCT clock divided by PRELH+1. Clear the counter (by writing a 1 to the CLRCTR bit) whenever changing the PRE value. 21 8 read-write LIMIT SCT limit event select register 0x8 32 read-write 0 0xFFFFFFFF LIMMSK_L If bit n is one, event n is used as a counter limit for the L or unified counter (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of events in this SCT. 0 8 read-write LIMMSK_H If bit n is one, event n is used as a counter limit for the H counter (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of events in this SCT. 16 8 read-write HALT SCT halt event select register 0xC 32 read-write 0 0xFFFFFFFF HALTMSK_L If bit n is one, event n sets the HALT_L bit in the CTRL register (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of events in this SCT. 0 8 read-write HALTMSK_H If bit n is one, event n sets the HALT_H bit in the CTRL register (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of events in this SCT. 16 8 read-write STOP SCT stop event select register 0x10 32 read-write 0 0xFFFFFFFF STOPMSK_L If bit n is one, event n sets the STOP_L bit in the CTRL register (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of events in this SCT. 0 8 read-write STOPMSK_H If bit n is one, event n sets the STOP_H bit in the CTRL register (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of events in this SCT. 16 8 read-write START SCT start event select register 0x14 32 read-write 0 0xFFFFFFFF STARTMSK_L If bit n is one, event n clears the STOP_L bit in the CTRL register (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of events in this SCT. 0 8 read-write STARTMSK_H If bit n is one, event n clears the STOP_H bit in the CTRL register (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of events in this SCT. 16 8 read-write COUNT SCT counter register 0x40 32 read-write 0 0xFFFFFFFF CTR_L When UNIFY = 0, read or write the 16-bit L counter value. When UNIFY = 1, read or write the lower 16 bits of the 32-bit unified counter. 0 16 read-write CTR_H When UNIFY = 0, read or write the 16-bit H counter value. When UNIFY = 1, read or write the upper 16 bits of the 32-bit unified counter. 16 16 read-write STATE SCT state register 0x44 32 read-write 0 0x1F001F STATE_L State variable. 0 5 read-write STATE_H State variable. 16 5 read-write INPUT SCT input register 0x48 32 read-write 0 0xFFFFFFFF AIN0 Input 0 state. Input 0 state on the last SCT clock edge. 0 1 read-only AIN1 Input 1 state. Input 1 state on the last SCT clock edge. 1 1 read-only AIN2 Input 2 state. Input 2 state on the last SCT clock edge. 2 1 read-only AIN3 Input 3 state. Input 3 state on the last SCT clock edge. 3 1 read-only SIN0 Input 0 state. Input 0 state following the synchronization specified by INSYNC. 16 1 read-only SIN1 Input 1 state. Input 1 state following the synchronization specified by INSYNC. 17 1 read-only SIN2 Input 2 state. Input 2 state following the synchronization specified by INSYNC. 18 1 read-only SIN3 Input 3 state. Input 3 state following the synchronization specified by INSYNC. 19 1 read-only REGMODE SCT match/capture mode register 0x4C 32 read-write 0 0xFFFFFFFF REGMOD_L Each bit controls one match/capture register (register 0 = bit 0, register 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 = register operates as match register. 1 = register operates as capture register. 0 8 read-write REGMOD_H Each bit controls one match/capture register (register 0 = bit 16, register 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 0 = register operates as match registers. 1 = register operates as capture registers. 16 8 read-write OUTPUT SCT output register 0x50 32 read-write 0 0xFFFF OUT Writing a 1 to bit n forces the corresponding output HIGH. Writing a 0 forces the corresponding output LOW (output 0 = bit 0, output 1 = bit 1, etc.). The number of bits = number of outputs in this SCT. 0 6 read-write OUTPUTDIRCTRL SCT output counter direction control register 0x54 32 read-write 0 0xFFFFFFFF SETCLR0 Set/clear operation on output 0. Value 0x3 is reserved. Do not program this value. 0 2 read-write INDEPENDENT Set and clear do not depend on the direction of any counter. 0 L_REVERSED Set and clear are reversed when counter L or the unified counter is counting down. 0x1 H_REVERSED Set and clear are reversed when counter H is counting down. Do not use if UNIFY = 1. 0x2 SETCLR1 Set/clear operation on output 1. Value 0x3 is reserved. Do not program this value. 2 2 read-write INDEPENDENT Set and clear do not depend on the direction of any counter. 0 L_REVERSED Set and clear are reversed when counter L or the unified counter is counting down. 0x1 H_REVERSED Set and clear are reversed when counter H is counting down. Do not use if UNIFY = 1. 0x2 SETCLR2 Set/clear operation on output 2. Value 0x3 is reserved. Do not program this value. 4 2 read-write INDEPENDENT Set and clear do not depend on the direction of any counter. 0 L_REVERSED Set and clear are reversed when counter L or the unified counter is counting down. 0x1 H_REVERSED Set and clear are reversed when counter H is counting down. Do not use if UNIFY = 1. 0x2 SETCLR3 Set/clear operation on output 3. Value 0x3 is reserved. Do not program this value. 6 2 read-write INDEPENDENT Set and clear do not depend on the direction of any counter. 0 L_REVERSED Set and clear are reversed when counter L or the unified counter is counting down. 0x1 H_REVERSED Set and clear are reversed when counter H is counting down. Do not use if UNIFY = 1. 0x2 SETCLR4 Set/clear operation on output 4. Value 0x3 is reserved. Do not program this value. 8 2 read-write INDEPENDENT Set and clear do not depend on the direction of any counter. 0 L_REVERSED Set and clear are reversed when counter L or the unified counter is counting down. 0x1 H_REVERSED Set and clear are reversed when counter H is counting down. Do not use if UNIFY = 1. 0x2 SETCLR5 Set/clear operation on output 5. Value 0x3 is reserved. Do not program this value. 10 2 read-write INDEPENDENT Set and clear do not depend on the direction of any counter. 0 L_REVERSED Set and clear are reversed when counter L or the unified counter is counting down. 0x1 H_REVERSED Set and clear are reversed when counter H is counting down. Do not use if UNIFY = 1. 0x2 RES SCT conflict resolution register 0x58 32 read-write 0 0xFFFFFFFF O0RES Effect of simultaneous set and clear on output 0. 0 2 read-write NO_CHANGE No change. 0 SET Set output (or clear based on the SETCLR0 field in the OUTPUTDIRCTRL register). 0x1 CLEAR Clear output (or set based on the SETCLR0 field). 0x2 TOGGLE_OUTPUT Toggle output. 0x3 O1RES Effect of simultaneous set and clear on output 1. 2 2 read-write NO_CHANGE No change. 0 SET Set output (or clear based on the SETCLR1 field in the OUTPUTDIRCTRL register). 0x1 CLEAR Clear output (or set based on the SETCLR1 field). 0x2 TOGGLE_OUTPUT Toggle output. 0x3 O2RES Effect of simultaneous set and clear on output 2. 4 2 read-write NO_CHANGE No change. 0 SET Set output (or clear based on the SETCLR2 field in the OUTPUTDIRCTRL register). 0x1 CLEAR Clear output n (or set based on the SETCLR2 field). 0x2 TOGGLE_OUTPUT Toggle output. 0x3 O3RES Effect of simultaneous set and clear on output 3. 6 2 read-write NO_CHANGE No change. 0 SET Set output (or clear based on the SETCLR3 field in the OUTPUTDIRCTRL register). 0x1 CLEAR Clear output (or set based on the SETCLR3 field). 0x2 TOGGLE_OUTPUT Toggle output. 0x3 O4RES Effect of simultaneous set and clear on output 4. 8 2 read-write NO_CHANGE No change. 0 SET Set output (or clear based on the SETCLR4 field in the OUTPUTDIRCTRL register). 0x1 CLEAR Clear output (or set based on the SETCLR4 field). 0x2 TOGGLE_OUTPUT Toggle output. 0x3 O5RES Effect of simultaneous set and clear on output 5. 10 2 read-write NO_CHANGE No change. 0 SET Set output (or clear based on the SETCLR5 field in the OUTPUTDIRCTRL register). 0x1 CLEAR Clear output (or set based on the SETCLR5 field). 0x2 TOGGLE_OUTPUT Toggle output. 0x3 DMA0REQUEST SCT DMA request 0 register 0x5C 32 read-write 0 0xC000FFFF DEV_0 If bit n is one, event n triggers DMA request 0 (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of events in this SCT. 0 6 read-write DRL0 A 1 in this bit triggers DMA request 0 when it loads the MATCH_L/Unified registers from the RELOAD_L/Unified registers. 30 1 read-write DRQ0 This read-only bit indicates the state of DMA Request 0. Note that if the related DMA channel is enabled and properly set up, it is unlikely that software will see this flag, it will be cleared rapidly by the DMA service. The flag remaining set could point to an issue with DMA setup. 31 1 read-write DMA1REQUEST SCT DMA request 1 register 0x60 32 read-write 0 0xC000FFFF DEV_1 If bit n is one, event n triggers DMA request 1 (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of events in this SCT. 0 6 read-write DRL1 A 1 in this bit triggers DMA request 1 when it loads the Match L/Unified registers from the Reload L/Unified registers. 30 1 read-write DRQ1 This read-only bit indicates the state of DMA Request 1. Note that if the related DMA channel is enabled and properly set up, it is unlikely that software will see this flag, it will be cleared rapidly by the DMA service. The flag remaining set could point to an issue with DMA setup. 31 1 read-write EVEN SCT event interrupt enable register 0xF0 32 read-write 0 0xFFFF IEN The SCT requests an interrupt when bit n of this register and the event flag register are both one (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of events in this SCT. 0 8 read-write EVFLAG SCT event flag register 0xF4 32 read-write 0 0xFFFF FLAG Bit n is one if event n has occurred since reset or a 1 was last written to this bit (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of events in this SCT. 0 8 read-write CONEN SCT conflict interrupt enable register 0xF8 32 read-write 0 0xFFFF NCEN The SCT requests an interrupt when bit n of this register and the SCT conflict flag register are both one (output 0 = bit 0, output 1 = bit 1, etc.). The number of bits = number of outputs in this SCT. 0 6 read-write CONFLAG SCT conflict flag register 0xFC 32 read-write 0 0xC000FFFF NCFLAG Bit n is one if a no-change conflict event occurred on output n since reset or a 1 was last written to this bit (output 0 = bit 0, output 1 = bit 1, etc.). The number of bits = number of outputs in this SCT. 0 6 read-write BUSERRL The most recent bus error from this SCT involved writing CTR L/Unified, STATE L/Unified, MATCH L/Unified, or the Output register when the L/U counter was not halted. A word write to certain L and H registers can be half successful and half unsuccessful. 30 1 read-write BUSERRH The most recent bus error from this SCT involved writing CTR H, STATE H, MATCH H, or the Output register when the H counter was not halted. 31 1 read-write SCTCAP0 SCT capture register of capture channel CAP_MATCH 0x100 32 read-write 0 0xFFFFFFFF CAPn_L When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the lower 16 bits of the 32-bit value at which this register was last captured. 0 16 read-write CAPn_H When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the upper 16 bits of the 32-bit value at which this register was last captured. 16 16 read-write SCTMATCH0 SCT match value register of match channels CAP_MATCH 0x100 32 read-write 0 0xFFFFFFFF MATCHn_L When UNIFY = 0, read or write the 16-bit value to be compared to the L counter. When UNIFY = 1, read or write the lower 16 bits of the 32-bit value to be compared to the unified counter. 0 16 read-write MATCHn_H When UNIFY = 0, read or write the 16-bit value to be compared to the H counter. When UNIFY = 1, read or write the upper 16 bits of the 32-bit value to be compared to the unified counter. 16 16 read-write SCTCAP1 SCT capture register of capture channel CAP_MATCH 0x104 32 read-write 0 0xFFFFFFFF CAPn_L When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the lower 16 bits of the 32-bit value at which this register was last captured. 0 16 read-write CAPn_H When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the upper 16 bits of the 32-bit value at which this register was last captured. 16 16 read-write SCTMATCH1 SCT match value register of match channels CAP_MATCH 0x104 32 read-write 0 0xFFFFFFFF MATCHn_L When UNIFY = 0, read or write the 16-bit value to be compared to the L counter. When UNIFY = 1, read or write the lower 16 bits of the 32-bit value to be compared to the unified counter. 0 16 read-write MATCHn_H When UNIFY = 0, read or write the 16-bit value to be compared to the H counter. When UNIFY = 1, read or write the upper 16 bits of the 32-bit value to be compared to the unified counter. 16 16 read-write SCTCAP2 SCT capture register of capture channel CAP_MATCH 0x108 32 read-write 0 0xFFFFFFFF CAPn_L When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the lower 16 bits of the 32-bit value at which this register was last captured. 0 16 read-write CAPn_H When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the upper 16 bits of the 32-bit value at which this register was last captured. 16 16 read-write SCTMATCH2 SCT match value register of match channels CAP_MATCH 0x108 32 read-write 0 0xFFFFFFFF MATCHn_L When UNIFY = 0, read or write the 16-bit value to be compared to the L counter. When UNIFY = 1, read or write the lower 16 bits of the 32-bit value to be compared to the unified counter. 0 16 read-write MATCHn_H When UNIFY = 0, read or write the 16-bit value to be compared to the H counter. When UNIFY = 1, read or write the upper 16 bits of the 32-bit value to be compared to the unified counter. 16 16 read-write SCTCAP3 SCT capture register of capture channel CAP_MATCH 0x10C 32 read-write 0 0xFFFFFFFF CAPn_L When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the lower 16 bits of the 32-bit value at which this register was last captured. 0 16 read-write CAPn_H When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the upper 16 bits of the 32-bit value at which this register was last captured. 16 16 read-write SCTMATCH3 SCT match value register of match channels CAP_MATCH 0x10C 32 read-write 0 0xFFFFFFFF MATCHn_L When UNIFY = 0, read or write the 16-bit value to be compared to the L counter. When UNIFY = 1, read or write the lower 16 bits of the 32-bit value to be compared to the unified counter. 0 16 read-write MATCHn_H When UNIFY = 0, read or write the 16-bit value to be compared to the H counter. When UNIFY = 1, read or write the upper 16 bits of the 32-bit value to be compared to the unified counter. 16 16 read-write SCTCAP4 SCT capture register of capture channel CAP_MATCH 0x110 32 read-write 0 0xFFFFFFFF CAPn_L When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the lower 16 bits of the 32-bit value at which this register was last captured. 0 16 read-write CAPn_H When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the upper 16 bits of the 32-bit value at which this register was last captured. 16 16 read-write SCTMATCH4 SCT match value register of match channels CAP_MATCH 0x110 32 read-write 0 0xFFFFFFFF MATCHn_L When UNIFY = 0, read or write the 16-bit value to be compared to the L counter. When UNIFY = 1, read or write the lower 16 bits of the 32-bit value to be compared to the unified counter. 0 16 read-write MATCHn_H When UNIFY = 0, read or write the 16-bit value to be compared to the H counter. When UNIFY = 1, read or write the upper 16 bits of the 32-bit value to be compared to the unified counter. 16 16 read-write SCTCAP5 SCT capture register of capture channel CAP_MATCH 0x114 32 read-write 0 0xFFFFFFFF CAPn_L When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the lower 16 bits of the 32-bit value at which this register was last captured. 0 16 read-write CAPn_H When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the upper 16 bits of the 32-bit value at which this register was last captured. 16 16 read-write SCTMATCH5 SCT match value register of match channels CAP_MATCH 0x114 32 read-write 0 0xFFFFFFFF MATCHn_L When UNIFY = 0, read or write the 16-bit value to be compared to the L counter. When UNIFY = 1, read or write the lower 16 bits of the 32-bit value to be compared to the unified counter. 0 16 read-write MATCHn_H When UNIFY = 0, read or write the 16-bit value to be compared to the H counter. When UNIFY = 1, read or write the upper 16 bits of the 32-bit value to be compared to the unified counter. 16 16 read-write SCTCAP6 SCT capture register of capture channel CAP_MATCH 0x118 32 read-write 0 0xFFFFFFFF CAPn_L When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the lower 16 bits of the 32-bit value at which this register was last captured. 0 16 read-write CAPn_H When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the upper 16 bits of the 32-bit value at which this register was last captured. 16 16 read-write SCTMATCH6 SCT match value register of match channels CAP_MATCH 0x118 32 read-write 0 0xFFFFFFFF MATCHn_L When UNIFY = 0, read or write the 16-bit value to be compared to the L counter. When UNIFY = 1, read or write the lower 16 bits of the 32-bit value to be compared to the unified counter. 0 16 read-write MATCHn_H When UNIFY = 0, read or write the 16-bit value to be compared to the H counter. When UNIFY = 1, read or write the upper 16 bits of the 32-bit value to be compared to the unified counter. 16 16 read-write SCTCAP7 SCT capture register of capture channel CAP_MATCH 0x11C 32 read-write 0 0xFFFFFFFF CAPn_L When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the lower 16 bits of the 32-bit value at which this register was last captured. 0 16 read-write CAPn_H When UNIFY = 0, read the 16-bit counter value at which this register was last captured. When UNIFY = 1, read the upper 16 bits of the 32-bit value at which this register was last captured. 16 16 read-write SCTMATCH7 SCT match value register of match channels CAP_MATCH 0x11C 32 read-write 0 0xFFFFFFFF MATCHn_L When UNIFY = 0, read or write the 16-bit value to be compared to the L counter. When UNIFY = 1, read or write the lower 16 bits of the 32-bit value to be compared to the unified counter. 0 16 read-write MATCHn_H When UNIFY = 0, read or write the 16-bit value to be compared to the H counter. When UNIFY = 1, read or write the upper 16 bits of the 32-bit value to be compared to the unified counter. 16 16 read-write SCTCAPCTRL0 SCT capture control register CAPCTRL_MATCHREL 0x200 32 read-write 0 0xFFFFFFFF CAPCONn_L If bit m is one, event m causes the CAPn_L (UNIFY = 0) or the CAPn (UNIFY = 1) register to be loaded (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 8 read-write CAPCONn_H If bit m is one, event m causes the CAPn_H (UNIFY = 0) register to be loaded (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 16 8 read-write SCTMATCHREL0 SCT match reload value register CAPCTRL_MATCHREL 0x200 32 read-write 0 0xFFFFFFFF RELOADn_L When UNIFY = 0, specifies the 16-bit value to be loaded into the MATCHn_L register. When UNIFY = 1, specifies the lower 16 bits of the 32-bit value to be loaded into the MATCHn register. 0 16 read-write RELOADn_H When UNIFY = 0, specifies the 16-bit to be loaded into the MATCHn_H register. When UNIFY = 1, specifies the upper 16 bits of the 32-bit value to be loaded into the MATCHn register. 16 16 read-write SCTCAPCTRL1 SCT capture control register CAPCTRL_MATCHREL 0x204 32 read-write 0 0xFFFFFFFF CAPCONn_L If bit m is one, event m causes the CAPn_L (UNIFY = 0) or the CAPn (UNIFY = 1) register to be loaded (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 8 read-write CAPCONn_H If bit m is one, event m causes the CAPn_H (UNIFY = 0) register to be loaded (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 16 8 read-write SCTMATCHREL1 SCT match reload value register CAPCTRL_MATCHREL 0x204 32 read-write 0 0xFFFFFFFF RELOADn_L When UNIFY = 0, specifies the 16-bit value to be loaded into the MATCHn_L register. When UNIFY = 1, specifies the lower 16 bits of the 32-bit value to be loaded into the MATCHn register. 0 16 read-write RELOADn_H When UNIFY = 0, specifies the 16-bit to be loaded into the MATCHn_H register. When UNIFY = 1, specifies the upper 16 bits of the 32-bit value to be loaded into the MATCHn register. 16 16 read-write SCTCAPCTRL2 SCT capture control register CAPCTRL_MATCHREL 0x208 32 read-write 0 0xFFFFFFFF CAPCONn_L If bit m is one, event m causes the CAPn_L (UNIFY = 0) or the CAPn (UNIFY = 1) register to be loaded (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 8 read-write CAPCONn_H If bit m is one, event m causes the CAPn_H (UNIFY = 0) register to be loaded (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 16 8 read-write SCTMATCHREL2 SCT match reload value register CAPCTRL_MATCHREL 0x208 32 read-write 0 0xFFFFFFFF RELOADn_L When UNIFY = 0, specifies the 16-bit value to be loaded into the MATCHn_L register. When UNIFY = 1, specifies the lower 16 bits of the 32-bit value to be loaded into the MATCHn register. 0 16 read-write RELOADn_H When UNIFY = 0, specifies the 16-bit to be loaded into the MATCHn_H register. When UNIFY = 1, specifies the upper 16 bits of the 32-bit value to be loaded into the MATCHn register. 16 16 read-write SCTCAPCTRL3 SCT capture control register CAPCTRL_MATCHREL 0x20C 32 read-write 0 0xFFFFFFFF CAPCONn_L If bit m is one, event m causes the CAPn_L (UNIFY = 0) or the CAPn (UNIFY = 1) register to be loaded (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 8 read-write CAPCONn_H If bit m is one, event m causes the CAPn_H (UNIFY = 0) register to be loaded (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 16 8 read-write SCTMATCHREL3 SCT match reload value register CAPCTRL_MATCHREL 0x20C 32 read-write 0 0xFFFFFFFF RELOADn_L When UNIFY = 0, specifies the 16-bit value to be loaded into the MATCHn_L register. When UNIFY = 1, specifies the lower 16 bits of the 32-bit value to be loaded into the MATCHn register. 0 16 read-write RELOADn_H When UNIFY = 0, specifies the 16-bit to be loaded into the MATCHn_H register. When UNIFY = 1, specifies the upper 16 bits of the 32-bit value to be loaded into the MATCHn register. 16 16 read-write SCTCAPCTRL4 SCT capture control register CAPCTRL_MATCHREL 0x210 32 read-write 0 0xFFFFFFFF CAPCONn_L If bit m is one, event m causes the CAPn_L (UNIFY = 0) or the CAPn (UNIFY = 1) register to be loaded (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 8 read-write CAPCONn_H If bit m is one, event m causes the CAPn_H (UNIFY = 0) register to be loaded (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 16 8 read-write SCTMATCHREL4 SCT match reload value register CAPCTRL_MATCHREL 0x210 32 read-write 0 0xFFFFFFFF RELOADn_L When UNIFY = 0, specifies the 16-bit value to be loaded into the MATCHn_L register. When UNIFY = 1, specifies the lower 16 bits of the 32-bit value to be loaded into the MATCHn register. 0 16 read-write RELOADn_H When UNIFY = 0, specifies the 16-bit to be loaded into the MATCHn_H register. When UNIFY = 1, specifies the upper 16 bits of the 32-bit value to be loaded into the MATCHn register. 16 16 read-write SCTCAPCTRL5 SCT capture control register CAPCTRL_MATCHREL 0x214 32 read-write 0 0xFFFFFFFF CAPCONn_L If bit m is one, event m causes the CAPn_L (UNIFY = 0) or the CAPn (UNIFY = 1) register to be loaded (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 8 read-write CAPCONn_H If bit m is one, event m causes the CAPn_H (UNIFY = 0) register to be loaded (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 16 8 read-write SCTMATCHREL5 SCT match reload value register CAPCTRL_MATCHREL 0x214 32 read-write 0 0xFFFFFFFF RELOADn_L When UNIFY = 0, specifies the 16-bit value to be loaded into the MATCHn_L register. When UNIFY = 1, specifies the lower 16 bits of the 32-bit value to be loaded into the MATCHn register. 0 16 read-write RELOADn_H When UNIFY = 0, specifies the 16-bit to be loaded into the MATCHn_H register. When UNIFY = 1, specifies the upper 16 bits of the 32-bit value to be loaded into the MATCHn register. 16 16 read-write SCTCAPCTRL6 SCT capture control register CAPCTRL_MATCHREL 0x218 32 read-write 0 0xFFFFFFFF CAPCONn_L If bit m is one, event m causes the CAPn_L (UNIFY = 0) or the CAPn (UNIFY = 1) register to be loaded (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 8 read-write CAPCONn_H If bit m is one, event m causes the CAPn_H (UNIFY = 0) register to be loaded (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 16 8 read-write SCTMATCHREL6 SCT match reload value register CAPCTRL_MATCHREL 0x218 32 read-write 0 0xFFFFFFFF RELOADn_L When UNIFY = 0, specifies the 16-bit value to be loaded into the MATCHn_L register. When UNIFY = 1, specifies the lower 16 bits of the 32-bit value to be loaded into the MATCHn register. 0 16 read-write RELOADn_H When UNIFY = 0, specifies the 16-bit to be loaded into the MATCHn_H register. When UNIFY = 1, specifies the upper 16 bits of the 32-bit value to be loaded into the MATCHn register. 16 16 read-write SCTCAPCTRL7 SCT capture control register CAPCTRL_MATCHREL 0x21C 32 read-write 0 0xFFFFFFFF CAPCONn_L If bit m is one, event m causes the CAPn_L (UNIFY = 0) or the CAPn (UNIFY = 1) register to be loaded (event 0 = bit 0, event 1 = bit 1, etc.). The number of bits = number of match/captures in this SCT. 0 8 read-write CAPCONn_H If bit m is one, event m causes the CAPn_H (UNIFY = 0) register to be loaded (event 0 = bit 16, event 1 = bit 17, etc.). The number of bits = number of match/captures in this SCT. 16 8 read-write SCTMATCHREL7 SCT match reload value register CAPCTRL_MATCHREL 0x21C 32 read-write 0 0xFFFFFFFF RELOADn_L When UNIFY = 0, specifies the 16-bit value to be loaded into the MATCHn_L register. When UNIFY = 1, specifies the lower 16 bits of the 32-bit value to be loaded into the MATCHn register. 0 16 read-write RELOADn_H When UNIFY = 0, specifies the 16-bit to be loaded into the MATCHn_H register. When UNIFY = 1, specifies the upper 16 bits of the 32-bit value to be loaded into the MATCHn register. 16 16 read-write 8 0x8 EVENT[%s] no description available 0x300 STATE SCT event state register 0 0 32 read-write 0 0xFFFF STATEMSKn If bit m is one, event n happens in state m of the counter selected by the HEVENT bit (n = event number, m = state number; state 0 = bit 0, state 1= bit 1, etc.). The number of bits = number of states in this SCT. 0 8 read-write CTRL SCT event control register 0 0x4 32 read-write 0 0x7FFFFF MATCHSEL Selects the Match register associated with this event (if any). A match can occur only when the counter selected by the HEVENT bit is running. 0 4 read-write HEVENT Select L/H counter. Do not set this bit if UNIFY = 1. 4 1 read-write L_COUNTER Selects the L state and the L match register selected by MATCHSEL. 0 H_COUNTER Selects the H state and the H match register selected by MATCHSEL. 0x1 OUTSEL Input/output select 5 1 read-write INPUT Selects the inputs selected by IOSEL. 0 OUTPUT Selects the outputs selected by IOSEL. 0x1 IOSEL Selects the input or output signal number associated with this event (if any). Do not select an input in this register if CKMODE is 1x. In this case the clock input is an implicit ingredient of every event. 6 4 read-write IOCOND Selects the I/O condition for event n. (The detection of edges on outputs lag the conditions that switch the outputs by one SCT clock). In order to guarantee proper edge/state detection, an input must have a minimum pulse width of at least one SCT clock period . 10 2 read-write LOW LOW 0 RISE Rise 0x1 FALL Fall 0x2 HIGH HIGH 0x3 COMBMODE Selects how the specified match and I/O condition are used and combined. 12 2 read-write OR OR. The event occurs when either the specified match or I/O condition occurs. 0 MATCH MATCH. Uses the specified match only. 0x1 IO IO. Uses the specified I/O condition only. 0x2 AND AND. The event occurs when the specified match and I/O condition occur simultaneously. 0x3 STATELD This bit controls how the STATEV value modifies the state selected by HEVENT when this event is the highest-numbered event occurring for that state. 14 1 read-write ADD STATEV value is added into STATE (the carry-out is ignored). 0 LOAD STATEV value is loaded into STATE. 0x1 STATEV This value is loaded into or added to the state selected by HEVENT, depending on STATELD, when this event is the highest-numbered event occurring for that state. If STATELD and STATEV are both zero, there is no change to the STATE value. 15 5 read-write MATCHMEM If this bit is one and the COMBMODE field specifies a match component to the triggering of this event, then a match is considered to be active whenever the counter value is GREATER THAN OR EQUAL TO the value specified in the match register when counting up, LESS THEN OR EQUAL TO the match value when counting down. If this bit is zero, a match is only be active during the cycle when the counter is equal to the match value. 20 1 read-write DIRECTION Direction qualifier for event generation. This field only applies when the counters are operating in BIDIR mode. If BIDIR = 0, the SCT ignores this field. Value 0x3 is reserved. 21 2 read-write DIRECTION_INDEPENDENT Direction independent. This event is triggered regardless of the count direction. 0 COUNTING_UP Counting up. This event is triggered only during up-counting when BIDIR = 1. 0x1 COUNTING_DOWN Counting down. This event is triggered only during down-counting when BIDIR = 1. 0x2 6 0x8 OUT[%s] no description available 0x500 SET SCT output 0 set register 0 32 read-write 0 0xFFFF SET A 1 in bit m selects event m to set output n (or clear it if SETCLRn = 0x1 or 0x2) output 0 = bit 0, output 1 = bit 1, etc. The number of bits = number of events in this SCT. When the counter is used in bi-directional mode, it is possible to reverse the action specified by the output set and clear registers when counting down, See the OUTPUTCTRL register. 0 8 read-write CLR SCT output 0 clear register 0x4 32 read-write 0 0xFFFF CLR A 1 in bit m selects event m to clear output n (or set it if SETCLRn = 0x1 or 0x2) event 0 = bit 0, event 1 = bit 1, etc. The number of bits = number of events in this SCT. When the counter is used in bi-directional mode, it is possible to reverse the action specified by the output set and clear registers when counting down, See the OUTPUTCTRL register. 0 8 read-write DMA0 LPC82x DMA controller DMA 0x50008000 0 0x51C registers DMA0 20 CTRL DMA control. 0 32 read-write 0 0x1 ENABLE DMA controller master enable. 0 1 read-write DISABLED Disabled. The DMA controller is disabled. This clears any triggers that were asserted at the point when disabled, but does not prevent re-triggering when the DMA controller is re-enabled. 0 ENABLED Enabled. The DMA controller is enabled. 0x1 INTSTAT Interrupt status. 0x4 32 read-only 0 0x6 ACTIVEINT Summarizes whether any enabled interrupts (other than error interrupts) are pending. 1 1 read-only NOT_PENDING Not pending. No enabled interrupts are pending. 0 PENDING Pending. At least one enabled interrupt is pending. 0x1 ACTIVEERRINT Summarizes whether any error interrupts are pending. 2 1 read-only NOT_PENDING Not pending. No error interrupts are pending. 0 PENDING Pending. At least one error interrupt is pending. 0x1 SRAMBASE SRAM address of the channel configuration table. 0x8 32 read-write 0 0xFFFFFE00 OFFSET Address bits 31:9 of the beginning of the DMA descriptor table. For 18 channels, the table must begin on a 512 byte boundary. 9 23 read-write ENABLESET0 Channel Enable read and Set for all DMA channels. 0x20 32 read-write 0 0xFFFFFFFF ENA Enable for DMA channels. Bit n enables or disables DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = disabled. 1 = enabled. 0 18 read-write ENABLECLR0 Channel Enable Clear for all DMA channels. 0x28 32 read-write 0 0 CLR Writing ones to this register clears the corresponding bits in ENABLESET0. Bit n clears the channel enable bit n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 18 read-write ACTIVE0 Channel Active status for all DMA channels. 0x30 32 read-only 0 0xFFFFFFFF ACT Active flag for DMA channel n. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = not active. 1 = active. 0 18 read-only BUSY0 Channel Busy status for all DMA channels. 0x38 32 read-only 0 0xFFFFFFFF BSY Busy flag for DMA channel n. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = not busy. 1 = busy. 0 18 read-only ERRINT0 Error Interrupt status for all DMA channels. 0x40 32 read-write 0 0xFFFFFFFF ERR Error Interrupt flag for DMA channel n. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = error interrupt is not active. 1 = error interrupt is active. 0 18 read-write INTENSET0 Interrupt Enable read and Set for all DMA channels. 0x48 32 read-write 0 0xFFFFFFFF INTEN Interrupt Enable read and set for DMA channel n. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = interrupt for DMA channel is disabled. 1 = interrupt for DMA channel is enabled. 0 18 read-write INTENCLR0 Interrupt Enable Clear for all DMA channels. 0x50 32 read-write 0 0 CLR Writing ones to this register clears corresponding bits in the INTENSET0. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 18 read-write INTA0 Interrupt A status for all DMA channels. 0x58 32 read-write 0 0xFFFFFFFF IA Interrupt A status for DMA channel n. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = the DMA channel interrupt A is not active. 1 = the DMA channel interrupt A is active. 0 18 read-write INTB0 Interrupt B status for all DMA channels. 0x60 32 read-write 0 0xFFFFFFFF IB Interrupt B status for DMA channel n. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = the DMA channel interrupt B is not active. 1 = the DMA channel interrupt B is active. 0 18 read-write SETVALID0 Set ValidPending control bits for all DMA channels. 0x68 32 read-write 0 0 SV SETVALID control for DMA channel n. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = no effect. 1 = sets the VALIDPENDING control bit for DMA channel n 0 18 read-write SETTRIG0 Set Trigger control bits for all DMA channels. 0x70 32 read-write 0 0 TRIG Set Trigger control bit for DMA channel 0. Bit n corresponds to DMA channel n. The number of bits = number of DMA channels in this device. Other bits are reserved. 0 = no effect. 1 = sets the TRIG bit for DMA channel n. 0 18 read-write ABORT0 Channel Abort control for all DMA channels. 0x78 32 read-write 0 0 ABORTCTRL Abort control for DMA channel 0. Bit n corresponds to DMA channel n. 0 = no effect. 1 = aborts DMA operations on channel n. 0 18 read-write 18 0x10 CHANNEL[%s] no description available 0x400 CFG Configuration register for DMA channel . 0 32 read-write 0 0x7CF73 PERIPHREQEN Peripheral request Enable. If a DMA channel is used to perform a memory-to-memory move, any peripheral DMA request associated with that channel can be disabled to prevent any interaction between the peripheral and the DMA controller. 0 1 read-write DISABLED Disabled. Peripheral DMA requests are disabled. 0 ENABLED Enabled. Peripheral DMA requests are enabled. 0x1 HWTRIGEN Hardware Triggering Enable for this channel. 1 1 read-write DISABLED Disabled. Hardware triggering is not used. 0 ENABLED Enabled. Use hardware triggering. 0x1 TRIGPOL Trigger Polarity. Selects the polarity of a hardware trigger for this channel. 4 1 read-write ACTIVE_LOW_FALLING Active low - falling edge. Hardware trigger is active low or falling edge triggered, based on TRIGTYPE. 0 ACTIVE_HIGH_RISING Active high - rising edge. Hardware trigger is active high or rising edge triggered, based on TRIGTYPE. 0x1 TRIGTYPE Trigger Type. Selects hardware trigger as edge triggered or level triggered. 5 1 read-write EDGE Edge. Hardware trigger is edge triggered. Transfers will be initiated and completed, as specified for a single trigger. 0 LEVEL Level. Hardware trigger is level triggered. Note that when level triggering without burst (BURSTPOWER = 0) is selected, only hardware triggers should be used on that channel. Transfers continue as long as the trigger level is asserted. Once the trigger is de-asserted, the transfer will be paused until the trigger is, again, asserted. However, the transfer will not be paused until any remaining transfers within the current BURSTPOWER length are completed. 0x1 TRIGBURST Trigger Burst. Selects whether hardware triggers cause a single or burst transfer. 6 1 read-write SINGLE Single transfer. Hardware trigger causes a single transfer. 0 BURST Burst transfer. When the trigger for this channel is set to edge triggered, a hardware trigger causes a burst transfer, as defined by BURSTPOWER. When the trigger for this channel is set to level triggered, a hardware trigger causes transfers to continue as long as the trigger is asserted, unless the transfer is complete. 0x1 BURSTPOWER Burst Power is used in two ways. It always selects the address wrap size when SRCBURSTWRAP and/or DSTBURSTWRAP modes are selected (see descriptions elsewhere in this register). When the TRIGBURST field elsewhere in this register = 1, Burst Power selects how many transfers are performed for each DMA trigger. This can be used, for example, with peripherals that contain a FIFO that can initiate a DMA operation when the FIFO reaches a certain level. 0000: Burst size = 1 (20). 0001: Burst size = 2 (21). 0010: Burst size = 4 (22). 1010: Burst size = 1024 (210). This corresponds to the maximum supported transfer count. others: not supported. The total transfer length as defined in the XFERCOUNT bits in the XFERCFG register must be an even multiple of the burst size. 8 4 read-write SRCBURSTWRAP Source Burst Wrap. When enabled, the source data address for the DMA is 'wrapped', meaning that the source address range for each burst will be the same. As an example, this could be used to read several sequential registers from a peripheral for each DMA burst, reading the same registers again for each burst. 14 1 read-write DISABLED Disabled. Source burst wrapping is not enabled for this DMA channel. 0 ENABLED Enabled. Source burst wrapping is enabled for this DMA channel. 0x1 DSTBURSTWRAP Destination Burst Wrap. When enabled, the destination data address for the DMA is 'wrapped', meaning that the destination address range for each burst will be the same. As an example, this could be used to write several sequential registers to a peripheral for each DMA burst, writing the same registers again for each burst. 15 1 read-write DISABLED Disabled. Destination burst wrapping is not enabled for this DMA channel. 0 ENABLED Enabled. Destination burst wrapping is enabled for this DMA channel. 0x1 CHPRIORITY Priority of this channel when multiple DMA requests are pending. Eight priority levels are supported: 0x0 = highest priority. 0x7 = lowest priority. 16 3 read-write CTLSTAT Control and status register for DMA channel . 0x4 32 read-only 0 0x5 VALIDPENDING Valid pending flag for this channel. This bit is set when a 1 is written to the corresponding bit in the related SETVALID register when CFGVALID = 1 for the same channel. 0 1 read-only NO_EFFECT No effect. No effect on DMA operation. 0 VALID_PENDING Valid pending. 0x1 TRIG Trigger flag. Indicates that the trigger for this channel is currently set. This bit is cleared at the end of an entire transfer or upon reload when CLRTRIG = 1. 2 1 read-only NOT_TRIGGERED Not triggered. The trigger for this DMA channel is not set. DMA operations will not be carried out. 0 TRIGGERED Triggered. The trigger for this DMA channel is set. DMA operations will be carried out. 0x1 XFERCFG Transfer configuration register for DMA channel . 0x8 32 read-write 0 0x3FFF33F CFGVALID Configuration Valid flag. This bit indicates whether the current channel descriptor is valid and can potentially be acted upon, if all other activation criteria are fulfilled. 0 1 read-write NOT_VALID Not valid. The channel descriptor is not considered valid until validated by an associated SETVALID0 setting. 0 VALID Valid. The current channel descriptor is considered valid. 0x1 RELOAD Indicates whether the channel's control structure will be reloaded when the current descriptor is exhausted. Reloading allows ping-pong and linked transfers. 1 1 read-write DISABLED Disabled. Do not reload the channels' control structure when the current descriptor is exhausted. 0 ENABLED Enabled. Reload the channels' control structure when the current descriptor is exhausted. 0x1 SWTRIG Software Trigger. 2 1 read-write NOT_SET Not set. When written by software, the trigger for this channel is not set. A new trigger, as defined by the HWTRIGEN, TRIGPOL, and TRIGTYPE will be needed to start the channel. 0 SET Set. When written by software, the trigger for this channel is set immediately. This feature should not be used with level triggering when TRIGBURST = 0. 0x1 CLRTRIG Clear Trigger. 3 1 read-write NOT_CLEARED Not cleared. The trigger is not cleared when this descriptor is exhausted. If there is a reload, the next descriptor will be started. 0 CLEARED Cleared. The trigger is cleared when this descriptor is exhausted 0x1 SETINTA Set Interrupt flag A for this channel. There is no hardware distinction between interrupt A and B. They can be used by software to assist with more complex descriptor usage. By convention, interrupt A may be used when only one interrupt flag is needed. 4 1 read-write NO_EFFECT No effect. 0 SET Set. The INTA flag for this channel will be set when the current descriptor is exhausted. 0x1 SETINTB Set Interrupt flag B for this channel. There is no hardware distinction between interrupt A and B. They can be used by software to assist with more complex descriptor usage. By convention, interrupt A may be used when only one interrupt flag is needed. 5 1 read-write NO_EFFECT No effect. 0 SET Set. The INTB flag for this channel will be set when the current descriptor is exhausted. 0x1 WIDTH Transfer width used for this DMA channel. 8 2 read-write BIT_8 8-bit. 8-bit transfers are performed (8-bit source reads and destination writes). 0 BIT_16 16-bit. 6-bit transfers are performed (16-bit source reads and destination writes). 0x1 BIT_32 32-bit. 32-bit transfers are performed (32-bit source reads and destination writes). 0x2 SRCINC Determines whether the source address is incremented for each DMA transfer. 12 2 read-write NO_INCREMENT No increment. The source address is not incremented for each transfer. This is the usual case when the source is a peripheral device. 0 WIDTH_X_1 1 x width. The source address is incremented by the amount specified by Width for each transfer. This is the usual case when the source is memory. 0x1 WIDTH_X_2 2 x width. The source address is incremented by 2 times the amount specified by Width for each transfer. 0x2 WIDTH_X_4 4 x width. The source address is incremented by 4 times the amount specified by Width for each transfer. 0x3 DSTINC Determines whether the destination address is incremented for each DMA transfer. 14 2 read-write NO_INCREMENT No increment. The destination address is not incremented for each transfer. This is the usual case when the destination is a peripheral device. 0 WIDTH_X_1 1 x width. The destination address is incremented by the amount specified by Width for each transfer. This is the usual case when the destination is memory. 0x1 WIDTH_X_2 2 x width. The destination address is incremented by 2 times the amount specified by Width for each transfer. 0x2 WIDTH_X_4 4 x width. The destination address is incremented by 4 times the amount specified by Width for each transfer. 0x3 XFERCOUNT Total number of transfers to be performed, minus 1 encoded. The number of bytes transferred is: (XFERCOUNT + 1) x data width (as defined by the WIDTH field). The DMA controller uses this bit field during transfer to count down. Hence, it cannot be used by software to read back the size of the transfer, for instance, in an interrupt handler. 0x0 = a total of 1 transfer will be performed. 0x1 = a total of 2 transfers will be performed. 0x3FF = a total of 1,024 transfers will be performed. 16 10 read-write GPIO LPC82x General Purpose I/O (GPIO) GPIO 0xA0000000 0 0x2484 registers B0_0 Byte pin registers for all port 0 and 1 GPIO pins 0 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_1 Byte pin registers for all port 0 and 1 GPIO pins 0x1 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_2 Byte pin registers for all port 0 and 1 GPIO pins 0x2 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_3 Byte pin registers for all port 0 and 1 GPIO pins 0x3 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_4 Byte pin registers for all port 0 and 1 GPIO pins 0x4 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_5 Byte pin registers for all port 0 and 1 GPIO pins 0x5 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_6 Byte pin registers for all port 0 and 1 GPIO pins 0x6 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_7 Byte pin registers for all port 0 and 1 GPIO pins 0x7 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_8 Byte pin registers for all port 0 and 1 GPIO pins 0x8 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_9 Byte pin registers for all port 0 and 1 GPIO pins 0x9 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_10 Byte pin registers for all port 0 and 1 GPIO pins 0xA 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_11 Byte pin registers for all port 0 and 1 GPIO pins 0xB 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_12 Byte pin registers for all port 0 and 1 GPIO pins 0xC 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_13 Byte pin registers for all port 0 and 1 GPIO pins 0xD 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_14 Byte pin registers for all port 0 and 1 GPIO pins 0xE 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_15 Byte pin registers for all port 0 and 1 GPIO pins 0xF 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_16 Byte pin registers for all port 0 and 1 GPIO pins 0x10 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_17 Byte pin registers for all port 0 and 1 GPIO pins 0x11 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_18 Byte pin registers for all port 0 and 1 GPIO pins 0x12 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_19 Byte pin registers for all port 0 and 1 GPIO pins 0x13 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_20 Byte pin registers for all port 0 and 1 GPIO pins 0x14 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_21 Byte pin registers for all port 0 and 1 GPIO pins 0x15 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_22 Byte pin registers for all port 0 and 1 GPIO pins 0x16 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_23 Byte pin registers for all port 0 and 1 GPIO pins 0x17 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_24 Byte pin registers for all port 0 and 1 GPIO pins 0x18 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_25 Byte pin registers for all port 0 and 1 GPIO pins 0x19 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_26 Byte pin registers for all port 0 and 1 GPIO pins 0x1A 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_27 Byte pin registers for all port 0 and 1 GPIO pins 0x1B 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write B0_28 Byte pin registers for all port 0 and 1 GPIO pins 0x1C 8 read-write 0 0x1 PBYTE Read: state of the pin PIOm_n, regardless of direction, masking, or alternate function, except that pins configured as analog I/O always read as 0. One register for each port pin. Supported pins depends on the specific device and package. Write: loads the pin's output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 1 read-write W0_0 Word pin registers for all port 0 and 1 GPIO pins 0x1000 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_1 Word pin registers for all port 0 and 1 GPIO pins 0x1004 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_2 Word pin registers for all port 0 and 1 GPIO pins 0x1008 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_3 Word pin registers for all port 0 and 1 GPIO pins 0x100C 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_4 Word pin registers for all port 0 and 1 GPIO pins 0x1010 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_5 Word pin registers for all port 0 and 1 GPIO pins 0x1014 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_6 Word pin registers for all port 0 and 1 GPIO pins 0x1018 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_7 Word pin registers for all port 0 and 1 GPIO pins 0x101C 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_8 Word pin registers for all port 0 and 1 GPIO pins 0x1020 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_9 Word pin registers for all port 0 and 1 GPIO pins 0x1024 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_10 Word pin registers for all port 0 and 1 GPIO pins 0x1028 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_11 Word pin registers for all port 0 and 1 GPIO pins 0x102C 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_12 Word pin registers for all port 0 and 1 GPIO pins 0x1030 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_13 Word pin registers for all port 0 and 1 GPIO pins 0x1034 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_14 Word pin registers for all port 0 and 1 GPIO pins 0x1038 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_15 Word pin registers for all port 0 and 1 GPIO pins 0x103C 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_16 Word pin registers for all port 0 and 1 GPIO pins 0x1040 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_17 Word pin registers for all port 0 and 1 GPIO pins 0x1044 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_18 Word pin registers for all port 0 and 1 GPIO pins 0x1048 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_19 Word pin registers for all port 0 and 1 GPIO pins 0x104C 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_20 Word pin registers for all port 0 and 1 GPIO pins 0x1050 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_21 Word pin registers for all port 0 and 1 GPIO pins 0x1054 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_22 Word pin registers for all port 0 and 1 GPIO pins 0x1058 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_23 Word pin registers for all port 0 and 1 GPIO pins 0x105C 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_24 Word pin registers for all port 0 and 1 GPIO pins 0x1060 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_25 Word pin registers for all port 0 and 1 GPIO pins 0x1064 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_26 Word pin registers for all port 0 and 1 GPIO pins 0x1068 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_27 Word pin registers for all port 0 and 1 GPIO pins 0x106C 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write W0_28 Word pin registers for all port 0 and 1 GPIO pins 0x1070 32 read-write 0 0xFFFFFFFF PWORD Read 0: pin PIOm_n is LOW. Write 0: clear output bit. Read 0xFFFF FFFF: pin PIOm_n is HIGH. Write any value 0x0000 0001 to 0xFFFF FFFF: set output bit. Only 0 or 0xFFFF FFFF can be read. Writing any value other than 0 will set the output bit. One register for each port pin. Supported pins depends on the specific device and package. 0 32 read-write DIR0 Direction registers 0x2000 32 read-write 0 0xFFFFFFFF DIRP Selects pin direction for pin PIOm_n (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = input. 1 = output. 0 29 read-write MASK0 Mask register 0x2080 32 read-write 0 0xFFFFFFFF MASKP Controls which bits corresponding to PIOm_n are active in the MPORT register (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read MPORT: pin state; write MPORT: load output bit. 1 = Read MPORT: 0; write MPORT: output bit not affected. 0 29 read-write PIN0 Port pin register 0x2100 32 read-write 0 0xFFFFFFFF PORT Reads pin states or loads output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: pin is low; write: clear output bit. 1 = Read: pin is high; write: set output bit. 0 29 read-write MPIN0 Masked port register 0x2180 32 read-write 0 0xFFFFFFFF MPORTP Masked port register (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: pin is LOW and/or the corresponding bit in the MASK register is 1; write: clear output bit if the corresponding bit in the MASK register is 0. 1 = Read: pin is HIGH and the corresponding bit in the MASK register is 0; write: set output bit if the corresponding bit in the MASK register is 0. 0 29 read-write SET0 Write: Set register for port Read: output bits for port 0x2200 32 read-write 0 0xFFFFFFFF SETP Read or set output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = Read: output bit: write: no operation. 1 = Read: output bit; write: set output bit. 0 29 read-write CLR0 Clear port 0x2280 32 read-write 0 0 CLRP Clear output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Clear output bit. 0 29 write-only NOT0 Toggle port 0x2300 32 read-write 0 0 NOTP Toggle output bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = no operation. 1 = Toggle output bit. 0 29 write-only DIRSET0 Set pin direction bits for port 0x2380 32 write-only 0 0 DIRSETP Set direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Set direction bit. 0 29 write-only DIRCLR0 Clear pin direction bits for port 0x2400 32 write-only 0 0 DIRCLRP Clear direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = No operation. 1 = Clear direction bit. 0 29 write-only DIRNOT0 Toggle pin direction bits for port 0x2480 32 write-only 0 0 DIRNOTP Toggle direction bits (bit 0 = PIOn_0, bit 1 = PIOn_1, etc.). Supported pins depends on the specific device and package. 0 = no operation. 1 = Toggle direction bit. 0 29 write-only PINT LPC82x Pin interrupt and pattern match (PINT) PINT 0xA0004000 0 0x34 registers PIN_INT0 24 PIN_INT1 25 PIN_INT2 26 PIN_INT3 27 PIN_INT4 28 PIN_INT5 29 PIN_INT6 30 PIN_INT7 31 ISEL Pin Interrupt Mode register 0 32 read-write 0 0xFF PMODE Selects the interrupt mode for each pin interrupt. Bit n configures the pin interrupt selected in PINTSELn. 0 = Edge sensitive 1 = Level sensitive 0 8 read-write IENR Pin interrupt level or rising edge interrupt enable register 0x4 32 read-write 0 0xFF ENRL Enables the rising edge or level interrupt for each pin interrupt. Bit n configures the pin interrupt selected in PINTSELn. 0 = Disable rising edge or level interrupt. 1 = Enable rising edge or level interrupt. 0 8 read-write SIENR Pin interrupt level or rising edge interrupt set register 0x8 32 write-only 0 0 SETENRL Ones written to this address set bits in the IENR, thus enabling interrupts. Bit n sets bit n in the IENR register. 0 = No operation. 1 = Enable rising edge or level interrupt. 0 8 write-only CIENR Pin interrupt level (rising edge interrupt) clear register 0xC 32 write-only 0 0 CENRL Ones written to this address clear bits in the IENR, thus disabling the interrupts. Bit n clears bit n in the IENR register. 0 = No operation. 1 = Disable rising edge or level interrupt. 0 8 write-only IENF Pin interrupt active level or falling edge interrupt enable register 0x10 32 read-write 0 0xFF ENAF Enables the falling edge or configures the active level interrupt for each pin interrupt. Bit n configures the pin interrupt selected in PINTSELn. 0 = Disable falling edge interrupt or set active interrupt level LOW. 1 = Enable falling edge interrupt enabled or set active interrupt level HIGH. 0 8 read-write SIENF Pin interrupt active level or falling edge interrupt set register 0x14 32 write-only 0 0 SETENAF Ones written to this address set bits in the IENF, thus enabling interrupts. Bit n sets bit n in the IENF register. 0 = No operation. 1 = Select HIGH-active interrupt or enable falling edge interrupt. 0 8 write-only CIENF Pin interrupt active level or falling edge interrupt clear register 0x18 32 write-only 0 0 CENAF Ones written to this address clears bits in the IENF, thus disabling interrupts. Bit n clears bit n in the IENF register. 0 = No operation. 1 = LOW-active interrupt selected or falling edge interrupt disabled. 0 8 write-only RISE Pin interrupt rising edge register 0x1C 32 read-write 0 0xFF RDET Rising edge detect. Bit n detects the rising edge of the pin selected in PINTSELn. Read 0: No rising edge has been detected on this pin since Reset or the last time a one was written to this bit. Write 0: no operation. Read 1: a rising edge has been detected since Reset or the last time a one was written to this bit. Write 1: clear rising edge detection for this pin. 0 8 read-write FALL Pin interrupt falling edge register 0x20 32 read-write 0 0xFF FDET Falling edge detect. Bit n detects the falling edge of the pin selected in PINTSELn. Read 0: No falling edge has been detected on this pin since Reset or the last time a one was written to this bit. Write 0: no operation. Read 1: a falling edge has been detected since Reset or the last time a one was written to this bit. Write 1: clear falling edge detection for this pin. 0 8 read-write IST Pin interrupt status register 0x24 32 read-write 0 0xFF PSTAT Pin interrupt status. Bit n returns the status, clears the edge interrupt, or inverts the active level of the pin selected in PINTSELn. Read 0: interrupt is not being requested for this interrupt pin. Write 0: no operation. Read 1: interrupt is being requested for this interrupt pin. Write 1 (edge-sensitive): clear rising- and falling-edge detection for this pin. Write 1 (level-sensitive): switch the active level for this pin (in the IENF register). 0 8 read-write PMCTRL Pattern match interrupt control register 0x28 32 read-write 0 0xFF000003 SEL_PMATCH Specifies whether the 8 pin interrupts are controlled by the pin interrupt function or by the pattern match function. 0 1 read-write PIN_INTERRUPT Pin interrupt. Interrupts are driven in response to the standard pin interrupt function. 0 PATTERN_MATCH Pattern match. Interrupts are driven in response to pattern matches. 0x1 ENA_RXEV Enables the RXEV output to the CPU and/or to a GPIO output when the specified boolean expression evaluates to true. 1 1 read-write DISABLED Disabled. RXEV output to the CPU is disabled. 0 ENABLED Enabled. RXEV output to the CPU is enabled. 0x1 PMAT This field displays the current state of pattern matches. A 1 in any bit of this field indicates that the corresponding product term is matched by the current state of the appropriate inputs. 24 8 read-write PMSRC Pattern match interrupt bit-slice source register 0x2C 32 read-write 0 0xFFFFFF00 SRC0 Selects the input source for bit slice 0 8 3 read-write INPUT0 Input 0. Selects the pin selected in the PINTSEL0 register as the source to bit slice 0. 0 INPUT1 Input 1. Selects the pin selected in the PINTSEL1 register as the source to bit slice 0. 0x1 INPUT2 Input 2. Selects the pin selected in the PINTSEL2 register as the source to bit slice 0. 0x2 INPUT3 Input 3. Selects the pin selected in the PINTSEL3 register as the source to bit slice 0. 0x3 INPUT4 Input 4. Selects the pin selected in the PINTSEL4 register as the source to bit slice 0. 0x4 INPUT5 Input 5. Selects the pin selected in the PINTSEL5 register as the source to bit slice 0. 0x5 INPUT6 Input 6. Selects the pin selected in the PINTSEL6 register as the source to bit slice 0. 0x6 INPUT7 Input 7. Selects the pin selected in the PINTSEL7 register as the source to bit slice 0. 0x7 SRC1 Selects the input source for bit slice 1 11 3 read-write INPUT0 Input 0. Selects the pin selected in the PINTSEL0 register as the source to bit slice 1. 0 INPUT1 Input 1. Selects the pin selected in the PINTSEL1 register as the source to bit slice 1. 0x1 INPUT2 Input 2. Selects the pin selected in the PINTSEL2 register as the source to bit slice 1. 0x2 INPUT3 Input 3. Selects the pin selected in the PINTSEL3 register as the source to bit slice 1. 0x3 INPUT4 Input 4. Selects the pin selected in the PINTSEL4 register as the source to bit slice 1. 0x4 INPUT5 Input 5. Selects the pin selected in the PINTSEL5 register as the source to bit slice 1. 0x5 INPUT6 Input 6. Selects the pin selected in the PINTSEL6 register as the source to bit slice 1. 0x6 INPUT7 Input 7. Selects the pin selected in the PINTSEL7 register as the source to bit slice 1. 0x7 SRC2 Selects the input source for bit slice 2 14 3 read-write INPUT0 Input 0. Selects the pin selected in the PINTSEL0 register as the source to bit slice 2. 0 INPUT1 Input 1. Selects the pin selected in the PINTSEL1 register as the source to bit slice 2. 0x1 INPUT2 Input 2. Selects the pin selected in the PINTSEL2 register as the source to bit slice 2. 0x2 INPUT3 Input 3. Selects the pin selected in the PINTSEL3 register as the source to bit slice 2. 0x3 INPUT4 Input 4. Selects the pin selected in the PINTSEL4 register as the source to bit slice 2. 0x4 INPUT5 Input 5. Selects the pin selected in the PINTSEL5 register as the source to bit slice 2. 0x5 INPUT6 Input 6. Selects the pin selected in the PINTSEL6 register as the source to bit slice 2. 0x6 INPUT7 Input 7. Selects the pin selected in the PINTSEL7 register as the source to bit slice 2. 0x7 SRC3 Selects the input source for bit slice 3 17 3 read-write INPUT0 Input 0. Selects the pin selected in the PINTSEL0 register as the source to bit slice 3. 0 INPUT1 Input 1. Selects the pin selected in the PINTSEL1 register as the source to bit slice 3. 0x1 INPUT2 Input 2. Selects the pin selected in the PINTSEL2 register as the source to bit slice 3. 0x2 INPUT3 Input 3. Selects the pin selected in the PINTSEL3 register as the source to bit slice 3. 0x3 INPUT4 Input 4. Selects the pin selected in the PINTSEL4 register as the source to bit slice 3. 0x4 INPUT5 Input 5. Selects the pin selected in the PINTSEL5 register as the source to bit slice 3. 0x5 INPUT6 Input 6. Selects the pin selected in the PINTSEL6 register as the source to bit slice 3. 0x6 INPUT7 Input 7. Selects the pin selected in the PINTSEL7 register as the source to bit slice 3. 0x7 SRC4 Selects the input source for bit slice 4 20 3 read-write INPUT0 Input 0. Selects the pin selected in the PINTSEL0 register as the source to bit slice 4. 0 INPUT1 Input 1. Selects the pin selected in the PINTSEL1 register as the source to bit slice 4. 0x1 INPUT2 Input 2. Selects the pin selected in the PINTSEL2 register as the source to bit slice 4. 0x2 INPUT3 Input 3. Selects the pin selected in the PINTSEL3 register as the source to bit slice 4. 0x3 INPUT4 Input 4. Selects the pin selected in the PINTSEL4 register as the source to bit slice 4. 0x4 INPUT5 Input 5. Selects the pin selected in the PINTSEL5 register as the source to bit slice 4. 0x5 INPUT6 Input 6. Selects the pin selected in the PINTSEL6 register as the source to bit slice 4. 0x6 INPUT7 Input 7. Selects the pin selected in the PINTSEL7 register as the source to bit slice 4. 0x7 SRC5 Selects the input source for bit slice 5 23 3 read-write INPUT0 Input 0. Selects the pin selected in the PINTSEL0 register as the source to bit slice 5. 0 INPUT1 Input 1. Selects the pin selected in the PINTSEL1 register as the source to bit slice 5. 0x1 INPUT2 Input 2. Selects the pin selected in the PINTSEL2 register as the source to bit slice 5. 0x2 INPUT3 Input 3. Selects the pin selected in the PINTSEL3 register as the source to bit slice 5. 0x3 INPUT4 Input 4. Selects the pin selected in the PINTSEL4 register as the source to bit slice 5. 0x4 INPUT5 Input 5. Selects the pin selected in the PINTSEL5 register as the source to bit slice 5. 0x5 INPUT6 Input 6. Selects the pin selected in the PINTSEL6 register as the source to bit slice 5. 0x6 INPUT7 Input 7. Selects the pin selected in the PINTSEL7 register as the source to bit slice 5. 0x7 SRC6 Selects the input source for bit slice 6 26 3 read-write INPUT0 Input 0. Selects the pin selected in the PINTSEL0 register as the source to bit slice 6. 0 INPUT1 Input 1. Selects the pin selected in the PINTSEL1 register as the source to bit slice 6. 0x1 INPUT2 Input 2. Selects the pin selected in the PINTSEL2 register as the source to bit slice 6. 0x2 INPUT3 Input 3. Selects the pin selected in the PINTSEL3 register as the source to bit slice 6. 0x3 INPUT4 Input 4. Selects the pin selected in the PINTSEL4 register as the source to bit slice 6. 0x4 INPUT5 Input 5. Selects the pin selected in the PINTSEL5 register as the source to bit slice 6. 0x5 INPUT6 Input 6. Selects the pin selected in the PINTSEL6 register as the source to bit slice 6. 0x6 INPUT7 Input 7. Selects the pin selected in the PINTSEL7 register as the source to bit slice 6. 0x7 SRC7 Selects the input source for bit slice 7 29 3 read-write INPUT0 Input 0. Selects the pin selected in the PINTSEL0 register as the source to bit slice 7. 0 INPUT1 Input 1. Selects the pin selected in the PINTSEL1 register as the source to bit slice 7. 0x1 INPUT2 Input 2. Selects the pin selected in the PINTSEL2 register as the source to bit slice 7. 0x2 INPUT3 Input 3. Selects the pin selected in the PINTSEL3 register as the source to bit slice 7. 0x3 INPUT4 Input 4. Selects the pin selected in the PINTSEL4 register as the source to bit slice 7. 0x4 INPUT5 Input 5. Selects the pin selected in the PINTSEL5 register as the source to bit slice 7. 0x5 INPUT6 Input 6. Selects the pin selected in the PINTSEL6 register as the source to bit slice 7. 0x6 INPUT7 Input 7. Selects the pin selected in the PINTSEL7 register as the source to bit slice 7. 0x7 PMCFG Pattern match interrupt bit slice configuration register 0x30 32 read-write 0 0xFFFFFF7F PROD_ENDPTS0 Determines whether slice 0 is an endpoint. 0 1 read-write NO_EFFECT No effect. Slice 0 is not an endpoint. 0 ENDPOINT endpoint. Slice 0 is the endpoint of a product term (minterm). Pin interrupt 0 in the NVIC is raised if the minterm evaluates as true. 0x1 PROD_ENDPTS1 Determines whether slice 1 is an endpoint. 1 1 read-write NO_EFFECT No effect. Slice 1 is not an endpoint. 0 ENDPOINT endpoint. Slice 1 is the endpoint of a product term (minterm). Pin interrupt 1 in the NVIC is raised if the minterm evaluates as true. 0x1 PROD_ENDPTS2 Determines whether slice 2 is an endpoint. 2 1 read-write NO_EFFECT No effect. Slice 2 is not an endpoint. 0 ENDPOINT endpoint. Slice 2 is the endpoint of a product term (minterm). Pin interrupt 2 in the NVIC is raised if the minterm evaluates as true. 0x1 PROD_ENDPTS3 Determines whether slice 3 is an endpoint. 3 1 read-write NO_EFFECT No effect. Slice 3 is not an endpoint. 0 ENDPOINT endpoint. Slice 3 is the endpoint of a product term (minterm). Pin interrupt 3 in the NVIC is raised if the minterm evaluates as true. 0x1 PROD_ENDPTS4 Determines whether slice 4 is an endpoint. 4 1 read-write NO_EFFECT No effect. Slice 4 is not an endpoint. 0 ENDPOINT endpoint. Slice 4 is the endpoint of a product term (minterm). Pin interrupt 4 in the NVIC is raised if the minterm evaluates as true. 0x1 PROD_ENDPTS5 Determines whether slice 5 is an endpoint. 5 1 read-write NO_EFFECT No effect. Slice 5 is not an endpoint. 0 ENDPOINT endpoint. Slice 5 is the endpoint of a product term (minterm). Pin interrupt 5 in the NVIC is raised if the minterm evaluates as true. 0x1 PROD_ENDPTS6 Determines whether slice 6 is an endpoint. 6 1 read-write NO_EFFECT No effect. Slice 6 is not an endpoint. 0 ENDPOINT endpoint. Slice 6 is the endpoint of a product term (minterm). Pin interrupt 6 in the NVIC is raised if the minterm evaluates as true. 0x1 CFG0 Specifies the match contribution condition for bit slice 0. 8 3 read-write CONSTANT_HIGH Constant HIGH. This bit slice always contributes to a product term match. 0 STICKY_RISING_EDGE Sticky rising edge. Match occurs if a rising edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x1 STICKY_FALLING_EDGE Sticky falling edge. Match occurs if a falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x2 STICKY_RISING_FALLING_EDGE Sticky rising or falling edge. Match occurs if either a rising or falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x3 HIGH_LEVEL High level. Match (for this bit slice) occurs when there is a high level on the input specified for this bit slice in the PMSRC register. 0x4 LOW_LEVEL Low level. Match occurs when there is a low level on the specified input. 0x5 CONSTANT_ZERO Constant 0. This bit slice never contributes to a match (should be used to disable any unused bit slices). 0x6 EVENT Event. Non-sticky rising or falling edge. Match occurs on an event - i.e. when either a rising or falling edge is first detected on the specified input (this is a non-sticky version of value 0x3) . This bit is cleared after one clock cycle. 0x7 CFG1 Specifies the match contribution condition for bit slice 1. 11 3 read-write CONSTANT_HIGH Constant HIGH. This bit slice always contributes to a product term match. 0 STICKY_RISING_EDGE Sticky rising edge. Match occurs if a rising edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x1 STICKY_FALLING_EDGE Sticky falling edge. Match occurs if a falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x2 STICKY_RISING_FALLING_EDGE Sticky rising or falling edge. Match occurs if either a rising or falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x3 HIGH_LEVEL High level. Match (for this bit slice) occurs when there is a high level on the input specified for this bit slice in the PMSRC register. 0x4 LOW_LEVEL Low level. Match occurs when there is a low level on the specified input. 0x5 CONSTANT_ZERO Constant 0. This bit slice never contributes to a match (should be used to disable any unused bit slices). 0x6 EVENT Event. Non-sticky rising or falling edge. Match occurs on an event - i.e. when either a rising or falling edge is first detected on the specified input (this is a non-sticky version of value 0x3) . This bit is cleared after one clock cycle. 0x7 CFG2 Specifies the match contribution condition for bit slice 2. 14 3 read-write CONSTANT_HIGH Constant HIGH. This bit slice always contributes to a product term match. 0 STICKY_RISING_EDGE Sticky rising edge. Match occurs if a rising edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x1 STICKY_FALLING_EDGE Sticky falling edge. Match occurs if a falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x2 STICKY_RISING_FALLING_EDGE Sticky rising or falling edge. Match occurs if either a rising or falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x3 HIGH_LEVEL High level. Match (for this bit slice) occurs when there is a high level on the input specified for this bit slice in the PMSRC register. 0x4 LOW_LEVEL Low level. Match occurs when there is a low level on the specified input. 0x5 CONSTANT_ZERO Constant 0. This bit slice never contributes to a match (should be used to disable any unused bit slices). 0x6 EVENT Event. Non-sticky rising or falling edge. Match occurs on an event - i.e. when either a rising or falling edge is first detected on the specified input (this is a non-sticky version of value 0x3) . This bit is cleared after one clock cycle. 0x7 CFG3 Specifies the match contribution condition for bit slice 3. 17 3 read-write CONSTANT_HIGH Constant HIGH. This bit slice always contributes to a product term match. 0 STICKY_RISING_EDGE Sticky rising edge. Match occurs if a rising edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x1 STICKY_FALLING_EDGE Sticky falling edge. Match occurs if a falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x2 STICKY_RISING_FALLING_EDGE Sticky rising or falling edge. Match occurs if either a rising or falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x3 HIGH_LEVEL High level. Match (for this bit slice) occurs when there is a high level on the input specified for this bit slice in the PMSRC register. 0x4 LOW_LEVEL Low level. Match occurs when there is a low level on the specified input. 0x5 CONSTANT_ZERO Constant 0. This bit slice never contributes to a match (should be used to disable any unused bit slices). 0x6 EVENT Event. Non-sticky rising or falling edge. Match occurs on an event - i.e. when either a rising or falling edge is first detected on the specified input (this is a non-sticky version of value 0x3) . This bit is cleared after one clock cycle. 0x7 CFG4 Specifies the match contribution condition for bit slice 4. 20 3 read-write CONSTANT_HIGH Constant HIGH. This bit slice always contributes to a product term match. 0 STICKY_RISING_EDGE Sticky rising edge. Match occurs if a rising edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x1 STICKY_FALLING_EDGE Sticky falling edge. Match occurs if a falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x2 STICKY_RISING_FALLING_EDGE Sticky rising or falling edge. Match occurs if either a rising or falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x3 HIGH_LEVEL High level. Match (for this bit slice) occurs when there is a high level on the input specified for this bit slice in the PMSRC register. 0x4 LOW_LEVEL Low level. Match occurs when there is a low level on the specified input. 0x5 CONSTANT_ZERO Constant 0. This bit slice never contributes to a match (should be used to disable any unused bit slices). 0x6 EVENT Event. Non-sticky rising or falling edge. Match occurs on an event - i.e. when either a rising or falling edge is first detected on the specified input (this is a non-sticky version of value 0x3) . This bit is cleared after one clock cycle. 0x7 CFG5 Specifies the match contribution condition for bit slice 5. 23 3 read-write CONSTANT_HIGH Constant HIGH. This bit slice always contributes to a product term match. 0 STICKY_RISING_EDGE Sticky rising edge. Match occurs if a rising edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x1 STICKY_FALLING_EDGE Sticky falling edge. Match occurs if a falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x2 STICKY_RISING_FALLING_EDGE Sticky rising or falling edge. Match occurs if either a rising or falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x3 HIGH_LEVEL High level. Match (for this bit slice) occurs when there is a high level on the input specified for this bit slice in the PMSRC register. 0x4 LOW_LEVEL Low level. Match occurs when there is a low level on the specified input. 0x5 CONSTANT_ZERO Constant 0. This bit slice never contributes to a match (should be used to disable any unused bit slices). 0x6 EVENT Event. Non-sticky rising or falling edge. Match occurs on an event - i.e. when either a rising or falling edge is first detected on the specified input (this is a non-sticky version of value 0x3) . This bit is cleared after one clock cycle. 0x7 CFG6 Specifies the match contribution condition for bit slice 6. 26 3 read-write CONSTANT_HIGH Constant HIGH. This bit slice always contributes to a product term match. 0 STICKY_RISING_EDGE Sticky rising edge. Match occurs if a rising edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x1 STICKY_FALLING_EDGE Sticky falling edge. Match occurs if a falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x2 STICKY_RISING_FALLING_EDGE Sticky rising or falling edge. Match occurs if either a rising or falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x3 HIGH_LEVEL High level. Match (for this bit slice) occurs when there is a high level on the input specified for this bit slice in the PMSRC register. 0x4 LOW_LEVEL Low level. Match occurs when there is a low level on the specified input. 0x5 CONSTANT_ZERO Constant 0. This bit slice never contributes to a match (should be used to disable any unused bit slices). 0x6 EVENT Event. Non-sticky rising or falling edge. Match occurs on an event - i.e. when either a rising or falling edge is first detected on the specified input (this is a non-sticky version of value 0x3) . This bit is cleared after one clock cycle. 0x7 CFG7 Specifies the match contribution condition for bit slice 7. 29 3 read-write CONSTANT_HIGH Constant HIGH. This bit slice always contributes to a product term match. 0 STICKY_RISING_EDGE Sticky rising edge. Match occurs if a rising edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x1 STICKY_FALLING_EDGE Sticky falling edge. Match occurs if a falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x2 STICKY_RISING_FALLING_EDGE Sticky rising or falling edge. Match occurs if either a rising or falling edge on the specified input has occurred since the last time the edge detection for this bit slice was cleared. This bit is only cleared when the PMCFG or the PMSRC registers are written to. 0x3 HIGH_LEVEL High level. Match (for this bit slice) occurs when there is a high level on the input specified for this bit slice in the PMSRC register. 0x4 LOW_LEVEL Low level. Match occurs when there is a low level on the specified input. 0x5 CONSTANT_ZERO Constant 0. This bit slice never contributes to a match (should be used to disable any unused bit slices). 0x6 EVENT Event. Non-sticky rising or falling edge. Match occurs on an event - i.e. when either a rising or falling edge is first detected on the specified input (this is a non-sticky version of value 0x3) . This bit is cleared after one clock cycle. 0x7