Parameter is set automatically during the calibration process. Options for changing parameter 1-98. Default 1. Parameter is set automatically during the calibration process. Options for changing parameter 2-99. Default 99. Virtual value set as a percentage level between parameters MIN (1%) and MAX. (99%). The Dimmer will set to this value after first switch on. It is required for warming up and switching dimmable compact fluorescent lamps and certain types of light sources. Options for changing parameter 1-99. Default 1. This parameter determines the time required for switching compact fluorescent lamps and certain types of light sources. Setting this parameter to 0 will disable the incandescence functionality. Available settings: 0-255 (0s - 25,5s) Available settings: 1-99 Default: 1 Available settings: 0-255 (0s - 2,55s) Default setting: 1 Available settings: 1-99 Default: 1 Available settings: 0-255 (0s - 2,55s) Default setting: 1 Saving state before power faillure. Default 1. Available settings: 0 - Function disabled; 1-32767 - time to turn off measured in seconds (1s - 9,1h) Default setting: 0 Activate/Deactive ALL ON/OFF. Default 255. Changing value of this parameter will force the calibration process. This parameter determines operating mode of the Dimmer (automatic/manual settings). Function based on the sudden power variation of a specific value, interpreted as a LOAD ERROR. Available settings: 0 - function disabled; 1-99 - percentage value of power variation, compared to standard power consumption, measured during the calibration procedure (to be interpreted as load error/burnt out bulb) Default setting: 30 Time of delay (in seconds) for power variation detection, interpreted as a LOAD ERROR or OVERLOAD detection (too much power connected to the Dimmer). Available settings: 0 - detection of a burnt out bulb disabled; 1-255 - delay time in seconds; Default setting: 5 If the parameter is active, switching on the Dimmer (S1 single click) will always set this brightness level. Available settings: 0 - function disabled; 1-99 - percentage level of brightness; Default setting: 0 Binary inputs type configuration. Default 0. The value sent to associated devices on single click. Double-click set lighting at 100%. Default 1. Parameter determines, which actions will not result in sending frames to association groups. Parameter values may be combined, e.g. 1+2=3 means that associations on switching on or off the Dimmer (single click) will not be sent. Available settings: 0-31 0 - all actions send to association groups; 1 - do not send when switching on the Dimmer (single click); 2 - do not send when switching off the Dimmer (single click); 4 - do not send when changing dimming level (holding and releasing); 8 - do not send on double click; 16 - send 0xFF value on double click; Default setting: 0 Parameter determines, which actions will not result in sending frames to association groups. Parameter values may be combined, e.g. 1+2=3 means that associations on switching on or off the Dimmer (single click) will not be sent. Available settings: 0-31 0 - all actions send to association groups; 1 - do not send when switching on the Dimmer (single click); 2 - do not send when switching off the Dimmer (single click); 4 - do not send when changing dimming level (holding and releasing); 8 - do not send on double click; 16 - send 0xFF value on double click; Default setting: 0 Switch no. 2 controls the Dimmer additionally (in 3-way switch mode). Function disabled for parameter 20 set to 2 (roller blind switch) This parameter defines how commands are sent in specified association groups: as secure or non-secure. Parameter is active only in Z-Wave network security mode. It does not apply to 1st Lifeline group. Parameter values may be combined, e.g. 1+2=3 means that 2nd & 3rd group are sent as secure. Available settings: 0-15 0 - all groups (II-V) sent as non-secure; 1 - 2nd group sent as secure; 2 - 3rd group sent as secure; 4 - 4th group sent as secure; 8 - 5th group sent as secure; 15 - all groups (II-V) sent as secure; Default setting: 15 SCENE ID depends on the switch type configurations. Default 0. Forced auto-calibration will set this parameter’s value to 2. Load control mode recognized during auto-calibration. Load control mode recognized during auto-calibration. Dimmability of the load Time required to warm up the filament of halogen bulb. This parameter determines the trigger of auto-calibration procedure, e.g. power on, load error, etc. Behaviour of the Dimmer after OVERCURRENT or SURGE Reaching the defined value will result in turning off the load. Additional apparent power limit of 350VA is active by default. Available settings: 0 - functionality disabled; 1-350 - 1W-350W; Default setting: 250 Response to General Purpose Alarm; Default 3. Response to Water Flooding Alarm; Default 2. Response to Smoke, CO or CO2 Alarm; Default 3. Response to Temperature Alarm; Default 1. Alarm state may be cancelled earlier, as a result of pressing the switches or sending the Z-Wave command frame. OVERLOAD alarm report (load power consumption too high) LOAD ERROR alarm report (no load, load failure, burnt out bulb) OVERCURRENT alarm report (short circuit, burnt out bulb causing overcurrent) SURGE alarm report (Dimmer output overvoltage) OVERHEAT (critical temperature) and VOLTAGE DROP (low voltage) alarm report The parameter defines the power level change that will result in a new power report being sent. The value is a percentage of the previous report. Available settings: 0 - power reports disabled; 1-100 (1-100%) - power report threshold; Default setting: 10 (10%) Parameter 52 defines a time period between consecutive reports. Timer is reset and counted from zero after each report. Available settings: 0 - periodic reports disabled; 1-32767 (1-32767 seconds); Default setting: 3600 (3600s) Energy level change which will result in sending a new energy report. Available settings: 0 - energy reports disabled; 1-255 (0,01 - 2,55 kWh) - report triggering threshold; Default setting: 10 (0,1 kWh) The Dimmer may include active power and energy consumed by itself in reports sent to the main controller. This parameter defines how to calculate active power. This parameter is useful in a case of 2-wire connection with light sources other than resistive. The parameter is set to 0 after forced auto-calibration. This parameter determines the approximate value of the power that will be reported by the device at its maximum brightness level. This parameter works only when parameter 58 has a value other than 0. Available settings: 0-500 (0-500W) - power consumed by the load at the maximum brightness level. Default setting: 0