// Copyright (c) 2015-2018 Khronos Group. This work is licensed under a // Creative Commons Attribution 4.0 International License; see // http://creativecommons.org/licenses/by/4.0/ [[extensions]] = Layers & Extensions This chapter describes required and recommended processes for writing formal extensions and layers for the Vulkan API. It is concerned with processes and registration, while fine-grained naming conventions are included in the <>. Prior to revision 1.0.19 of the <>, most of the content in this chapter existed as part of Appendix C of that document. [NOTE] .Note ==== The mechanism and process of specifying extensions is subject to change, as we receive feedback from authors and further requirements of documentation tooling. This document will be updated as changes are made. ==== == Introduction The Khronos extension registries and extension naming conventions serve several purposes: * Avoiding naming collisions between extensions developed by mutually unaware parties, both in the extension names themselves, as well as their token, command, and type names. * Allocating enumerant values for tokens added by extensions * Creating a defined order between extensions. Extensions with higher numbers may have dependencies upon extensions with lower numbers, and must define any relevant interactions with lower-numbered extensions. * Provides a central repository for documentation and header changes associated with extensions Vulkan's design and general software development trends introduces two new paradigms that require rethinking the existing mechanisms: * Layers, and with them a focus on a more open ecosystem where non-Khronos members are expected to extend a Khronos API using the Layer mechanism. * Namespaced constants (enumerations) that do not necessarily draw from a single global set of token values. [[extensions-rules]] == General Rules/Guidelines Some general rules to simplify the specific rules below: * Extensions and layers must each have a globally unique name. * All commands and tokens must have a globally unique name. * Extensions can expose new commands, types, and/or tokens, but layers must not. ** However, layers can expose their own extensions, which in turn are allowed to expose new commands and tokens. * All extensions must be registered with Khronos. * Extensions in general are strictly additive and backwards-compatible with each other and with the core API. However, as described in more detail the Fundamentals chapter of the <>, explicit incompatibilities may exist, and must be documented. [[extensions-naming-conventions]] == Extension and Layer Naming Conventions Extensions and layers have formal _names_. These names are used in a variety of places: * When specifying extensions and layers to enable in the API. * As a preprocessor symbol in the `vulkan.h` header file indicating that an extension interface is defined at compile time. * To control building the Vulkan Specification from asciidoc source containing many extension, by explicitly enabling inclusion of one or more extensions. [NOTE] .Note ==== In version 1.0.24 and earlier versions of the Vulkan Specification, extensions were maintained in separate git branches from the core Specification source. This proved to be unwieldy and difficult to maintain as the core was repeatedly updated, and as of version 1.0.25, we have moved to a "`single-branch`" model in which most extensions can optionally be included or not from a single set of source documents. It is possible that some vendors will choose to continue maintaining their extension branches, and the existing extension branches will not be removed from GitHub. ==== There is a rigid syntax for these names: * Extensions are named with the syntax: `VK_AUTHOR_`. * Layers are named with the syntax: `VK_LAYER_{AUTHOR|FQDN}_`. Both extensions and layer names include a `VK_` prefix, as described in the <> section above. In addition, layers add a `LAYER_` prefix. Extension and layer names must both be valid C language identifiers. [[extensions-naming-conventions-name-strings]] === Extension and Layer Name Strings The `` portion of extension and layer names is a concise name describing the purpose or functionality of the extension or layer. The underscore (`_`) character is used as a delimiter between words. Every character of the name must be in lower case. [[extensions-naming-author-IDs]] === Author IDs Extension and layer names also contain an _author ID_, indicated by `AUTHOR` above, identifying the author of the extension/layer. This ID is a short, capitalized string identifying an author, such as a Khronos member developing Vulkan implementations for their devices, or a non-Khronos developer creating Vulkan layers. Author IDs must be registered with Khronos. Some authors have platform communities they wish to distinguish between, and can register additional author IDs for that purpose. For example, Google has separate Android and Chrome communities. Details on how to register an author ID are provided below. Layer authors not wishing to register an author ID with Khronos can instead use a fully-qualified domain name (FQDN) as the ID. The FQDN should be a domain name owned by the author. FQDNs cannot be used for extensions, only for layers. * The following are examples of extension and layer names, demonstrating the above syntax: ** Extension names all use the base prefix `VK_`. ** Khronos-ratified extensions add one of the reserved author IDs `KHR` or `KHX`, and will use the prefix `VK_KHR_` or `VK_KHX_`, respectively. ** The following author IDs are reserved and must not be used: *** `VK` - To avoid confusion with the top-level `VK_` prefix. *** `VULKAN` - To avoid confusion with the name of the Vulkan API. *** `LAYER` - To avoid confusion with the higher-level "`LAYER`" prefix. *** `KHRONOS` - To avoid confusion with the Khronos organization. ** Multi-author extensions that have not been ratified by Khronos (those developed via cooperation between, and intended to be supported by two or more registered authors) add the special author ID `EXT` to the base prefix, and will use the prefix `VK_EXT_`. ** Traditional author-specific extensions developed by one author (or one author in cooperation with non-authors) add the author ID to the base prefix. For example, NVIDIA will use the prefix `VK_NV_`, and Valve will use the prefix `VK_VALVE_`. Some authors can have additional registered author IDs for special purposes. For example, an Android extension developed by Google - but part of an Android open-source community project, and so not a proprietary Google extension - will use the author ID `ANDROID`. ** Layer names follow the same conventions as extensions, but use the base prefix `VK_LAYER_`. ** Because layers need not be registered with Khronos, an alternative mechanism is needed to allow creating unique layer names without registering an author ID. Layer authors that prefer not to register an author ID can instead use a fully-qualified domain name (FQDN) in reverse-order as an author ID, replacing `.` (period) with `_` (underscore) characters. The restriction that layer names must be valid C identifiers means that some FQDNs cannot be used as part of layer names. [NOTE] .Note ==== The `KHX` author ID is used for _experimental_ extensions, as described in the "`Layers & Extensions`" appendix of the <>. ==== [source, c] .Example ---- // Khronos extension name VK_KHR_mirror_clamp_to_edge // Multivendor extension name VK_EXT_debug_marker // Vendor extension name using author ID NV VK_NV_glsl_shader // Vendor layer name using author ID LUNARG VK_LAYER_LUNARG_vktrace // Layer name using the FQDN www.3dxcl.invalid instead of an author ID VK_LAYER_invalid_3dxcl_www ---- [NOTE] .Note ==== To avoid linking to a nonexistent domain, the reserved TLD `.invalid` is used in the example above. ==== [[extensions-naming]] == Extension Command, Type, and Token Naming Conventions Extensions may add new commands, types, and tokens, or collectively "`objects`", to the Vulkan API. These objects are given globally unique names by appending the author ID defined above for the extension name as described in the <> section above. [[extensions-api-registry]] == The Vulkan Registry The canonical definition of the Vulkan APIs is kept in an XML file known as the *Vulkan registry*. The registry is kept in `src/spec/vk.xml` in the `1.0` branch of the <> project, containing the most recently released Vulkan API specification. The registry contains reserved author IDs, core and extension interface definitions, definitions of individual commands and structures, and other information which must be agreed on by all implementations. The registry is used to maintain a single, consistent global namespace for the registered entities, to generate the Khronos-supplied `vulkan.h`, and to create a variety of related documentation used in generating the API specification and reference pages. [[extensions-author-ID]] == Registering an Author ID with Khronos Previous Khronos APIs could only officially be modified by Khronos members. In an effort to build a more flexible platform, Vulkan allows non-Khronos developers to extend and modify the API via layers and extensions in the same manner as Khronos members. However, extensions must still be registered with Khronos. A mechanism for non-members to register layers and extensions is provided. Extension authors will be able to create an account on GitHub and register an author ID with Khronos through the <> project. The author ID must be used for any extensions that author registers. The same mechanism will be used to request registration of extensions or layers with Khronos, as described below. To reserve an author ID, propose a merge request against <> in the `1.0` branch. The merge must add a `` XML tag and fill in the `name`, `author` and +contact+ attributes with the requested author ID, the author's formal name (e.g. company or project name), and contact email address, respectively. The author ID will only be reserved once this merge request is accepted. Please do not try to reserve author IDs which clearly belong to another existing company or software project which may wish to develop Vulkan extensions or layers in the future, as a matter of courtesy and respect. Khronos may decline to register author IDs that are not requested in good faith. [[extensions-vendor-id]] == Registering a Vendor ID with Khronos Vulkan implementers must report a valid vendor ID for their implementation when queried by fname:vkGetPhysicalDeviceProperties, as described in the "`Devices and Queues`" section of the <>. If there is no valid PCI vendor ID defined for the physical device, implementations must obtain a Khronos vendor ID. Khronos vendor IDs are reserved in a similar fashion to <>. While vendor IDs are not directly related to API extensions, the reservation process is very similar and so is described in this section. To reserve an Khronos vendor ID, you must first have a Khronos author ID. Propose a merge request against <> in the +1.0+ branch. The merge must add a `` tag and fill in the `name` and `id` attributes. The `name` attribute must be set to the author ID. The `id` attribute must be the first sequentially available ID in the list of `` tags. The vendor ID will be reserved only once this merge request has been accepted. Please do not try to reserve vendor IDs unless you are making a good faith effort to develop a Vulkan implementation and require one for that purpose. == Registering Extensions and Layers Extensions must be registered with Khronos. Layers should be registered, but registration is not required. Registration means: * Receiving an extension number. * Adding the extension or layer name to the list in `vk.xml` and appearing on the Khronos registry website, which will link to associated documentation hosted on Khronos. * For extensions which add to the Vulkan API, including definitions of those additions to `vk.xml`. Registration for Khronos members is handled by filing a merge request in the internal gitlab repository against the branch containing the core specification against which the extension or layer will be written. The merge must modify `vk.xml` to define extension names, API interfaces, and related information. Registration is not complete until the registry maintainer has validated and accepted the merge. Since this process could in principle be completely automated, this suggests a scalable mechanism for accepting registration of non-Khronos extensions. Non-Khronos members who want to create extensions must register with Khronos by creating a GitHub account, and registering their author ID and/or FQDNs to that account. They can then submit new extension registration requests by proposing merges to `vk.xml`. On acceptance of the merge, the extension will be registered, though its specification need not be checked into the Khronos GitHub repository at that point. The registration process can be split into several steps to accommodate extension number assignment prior to extension publication: * Acquire an extension number. This is done by proposing a merge request against `vk.xml` similarly to how <>. The merge should add a new `` tag at the end of the file with attributes specifying the proposed extension `name`, the next unused sequential extension `number`, the `author` and `contact` information (if different than that already specified for the author ID used in the extension name), and finally, specifying `supported="disabled"`. The extension number will be reserved only once this merge request is accepted into the `1.0` branch. * Develop and test the extension using the registered extension number. * Publish the extension to Khronos using the previously registered extension number, by submitting merge requests to the `1.0` branch defining the changes specific to the extension. Changes to both the specification source, and to `vk.xml` will be needed. ** Extension changes to the specification source must be protected by asciidoc conditionals as described in the <> section. ** Changes to `vk.xml` must define the extension interfaces in the `` block, and must also change the `supported` attribute value of the `` to `supported="vulkan"`. ** When publishing an extension, mark it as enabled by proposing a merge to the `1.0` branch changing the `supported` attribute value of the `` to `supported="vulkan"`. This should be completely automated and under the control of the publishers, to allow them to align publication on Khronos with product releases. However, complete automation might be difficult, since steps such as regenerating and validating `vulkan.h` are involved. Once the merge is accepted and the corresponding updated header with the new extension interface is committed to the `1.0` branch, publication is complete. ** Publishing on the <> is preferred whenever possible. Khronos members may instead create branches on Khronos' internal gitlab server, but those branches will eventually be mirrored to GitHub. ** Once the merge request defining an extension has been accepted into the `1.0` branch, publication is complete - although it may not be visible on GitHub until the next regular core Specification update is pushed out. * It is still possible to publish a separate branch of the repository with appropriate changes relative to the core Vulkan API branch instead, but this approach is deprecated and discouraged. If this is done, all changes to `vk.xml` must still be made in the `1.0` branch. ifdef::editing-notes[] [NOTE] .editing-note ==== TODO: This section is subject to change and not complete yet, but in broad is how we expect extension registration and specifications to work. The process will be refined as members and outside authors define further extensions. ==== endif::editing-notes[] [[extensions-documenting]] == Documenting Extensions Extensions are documented as modifications to the Vulkan specification. Changes specific to an extension are protected by asciidoc conditionals. The changes are only visible in generated documentation when the Specification is built with an asciidoc attribute of that name defined. [NOTE] .Note ==== This is referred to as the "`single-branch`" model, in contrast to the earlier model where each extension lived in a separate branch from the `1.0` core Specification source. ==== For example, the `VK_KHR_surface` extension is now documented in the `1.0` branch of the GitHub `<>` project. However, specifications generated from this branch will only include the extension when the Makefile is invoked appropriately. Most language defining extensions can be localized either into a small number of asciidoc include files which are conditionally included in the core specification chapters and appendices, or into parts of `vk.xml` defining the extension interfaces. [NOTE] .Note ==== We do not yet fully document an example of including an extension in the single-branch model. Instead, authors should refer to the `1.0` branch and search for the names of existing extensions, such as `VK_KHR_surface`, as examples. Some aspects of the changes for this example extension are described below. ==== The KHR extensions were used to help prototype what changes need to be made for extensions, which include (but may not be limited to) the following: * All extensions must add an appendix to the Vulkan specification. The appendix should be modeled after the `VK_KHR_shader_draw_parameters` extension in `doc/specs/vulkan/appendices/VK_KHR_shader_draw_parameters.txt`, which contains metainformation about the extension (as well as code examples, and revision history). This example is complicated because `VK_KHR_shader_draw_parameters` has a variety of external dependencies and interactions. The `VK_EXT_debug_marker` extension is a simpler, standalone example. * In the preamble to the appendix, start with an asciidoc `include` of the automatically generated meta information. This information includes the extension name string, type, number, revision, and contact information from +vk.xml+. * Following the `include`, add as many of the following sections as are meaningful: ** *Status* - *Complete*, *Draft*, or other. When an extension is published in the 1.0 branch, it is normally assumed to be complete; the *Status* field should be removed at this time, unless it contains additional information. ** *Last Modified Date* - if wanted, although git log queries can provide equivalent information. ** *IP Status* - Such as *No known IP claims*. ** *Interactions and External Dependencies* - may include requirements or interactions with optional Vulkan features, SPIR-V (+SPV+) and OpenGL extensions, and interactions (other than strictly requiring) with other Vulkan extensions. ** *Contributors* - Names and corporate affiliations of people who have made significant direct contributions to this extension. * Each extension's appendix file is included by adding an `include` statement to the `doc/specs/vulkan/appendices/extensions.txt` file. The `include` statement must be protected by appropriate asciidoc conditionals. The new file is grouped alphabetically by name, in a section of extensions sharing the same author ID. For example, for `VK_EXT_debug_marker`, `appendices.txt` is modified to add: + [source,asciidoc] .Example Markup ---- \ifdef::VK_EXT_debug_marker[] \include::appendices/VK_EXT_debug_marker.txt[] \endif::VK_EXT_debug_marker[] ---- * Extensions usually make significant additions and changes to the Vulkan specification. They often add an entirely new chapter, or a new section of an existing chapter, defining the new functions, structures, and enumerants. For example, in the case of `VK_EXT_debug_marker`, it adds a new section of the "`Debugging`" chapter in `chapters/debugging.txt`, by including in that file: + [source,asciidoc] .Example Markup ---- \ifdef::VK_EXT_debug_marker[] \include::chapters/VK_EXT_debug_marker/wsi.txt[] \endif::VK_EXT_debug_marker[] ---- * In every other place where the extension alters the behavior of the core Specification, make such changes and protect the modifications with the same asciidoc conditionals. For example, `VK_KHR_surface` adds new error codes to Vulkan. These are added to `chapters/fundamentals.txt` in the "`Return Codes`" section as follows: + [source,asciidoc] .Example Markup ---- ... list of existing error codes \ifdef::VK_KHR_surface[] \include::VK_KHR_surface/VkResultErrorDescriptions_surface.txt[] \endif::VK_KHR_surface[] ---- * If two extensions interact, the asciidoc conditionals must be carefully structured so as to properly document the interactions if the specification is built with both extensions. Asciidoc conditionals allow "and" and "or" constructs (see: http://asciidoctor.org/docs/user-manual/#conditional-preprocessor-directives and http://asciidoctor.org/docs/user-manual/#checking-multiple-attributes-ifdef-and-ifndef-only). + [source,asciidoc] .Example Markup ---- \ifdef::VK_KHR_foo[] ... discussion of VK_KHR_foo ... \ifdef::VK_KHR_fum[] ... discussion of interactions between VK_KHR_foo and VK_KHR_fum ... \endif::VK_KHR_fum[] \endif::VK_KHR_foo[] \ifdef::VK_KHR_fum[] ... discussion of VK_KHR_fum ... \endif::VK_KHR_fum[] ---- * In cases where a new extension (A) modifies both core and an existing extension (B), if the new extension (A) becomes part of the core at a future release (i.e. is no longer an extension), the portion of the new extension that modified the existing extension (B) effectively becomes part of that existing extension. Thus, at the new core release, enabling the pre-existing extension (B) also enables the functionality that was previously enabled by enabling the previously-new extension (A). * For vendor extensions, changes made to existing core Specification source files and to `vk.xml` all fall under the Contributor License Agreement. Vendors may use their own copyright on new files they add to the `1.0` branch, although that copyright must be compatible with the Specification copyright. * In most cases, there will be at most two new files added to the specification: `extensions/*extension_name*.txt`, and `chapters/*extension_name*.txt`. If you need more than one new file in either the `chapters/` or `extensions/` directories, create a subdirectory named with the extension name and place the new files there. For example, instead of `chapters/VK_KHR_android_surface.txt`, there is `chapters/VK_KHR_android_surface/platformCreateSurface_android.txt` and `chapters/VK_KHR_android_surface/platformQuerySupport_android.txt`, both of which are conditionally included elsewhere in the core specification files. * Valid Usage statements referring to interactions between structures in a pname:pNext chain must be described in the parent structure's language, as specified <>. * Valid Usage statements must: be kept atomic with regards to extension conditionals - do not surround part of a single statement with conditionals. Valid usage statements are automatically extracted from the specification for use by ecosystem components like the validation layers, and the extraction scripts need to know which valid usage statements apply to which extensions. The loops required to deal with partial statements are simply not worth the trouble. For example, instead of + [source,asciidoc] .Example Markup ---- * If pname:buffer was created with a sharing mode of ename:VK_SHARING_MODE_EXCLUSIVE, pname:srcQueueFamilyIndex and pname:dstQueueFamilyIndex must: either both be ename:VK_QUEUE_FAMILY_IGNORED, or both be a valid queue family (see <>) \ifdef::VK_KHX_external_memory[] unless one of them is ename:VK_QUEUE_FAMILY_EXTERNAL_KHX and the other is ename:VK_QUEUE_FAMILY_IGNORED. \endif::VK_KHX_external_memory[] ---- + Use + [source,asciidoc] .Example Markup ---- ifndef::VK_KHX_external_memory[] * If pname:buffer was created with a sharing mode of ename:VK_SHARING_MODE_EXCLUSIVE, pname:srcQueueFamilyIndex and pname:dstQueueFamilyIndex must: either both be ename:VK_QUEUE_FAMILY_IGNORED, or both be a valid queue family (see <>) endif::VK_KHX_external_memory[] ifdef::VK_KHX_external_memory[] * If pname:buffer was created with a sharing mode of ename:VK_SHARING_MODE_EXCLUSIVE, pname:srcQueueFamilyIndex and pname:dstQueueFamilyIndex must: either both be ename:VK_QUEUE_FAMILY_IGNORED, both be a valid queue family (see <>), or be ename:VK_QUEUE_FAMILY_EXTERNAL_KHX and ename:VK_QUEUE_FAMILY_IGNORED in either order endif::VK_KHX_external_memory[] ---- == Assigning Extension Token Values Extensions can define their own enumeration types and assign any values to their enumerants that they like. Each enumeration has a private namespace, so collisions are not a problem. However, when extending existing enumeration objects with new values, care must be taken to preserve global uniqueness of values. Enumerations which define new bits in a bitmask are treated specially as described in <> below. Each extension is assigned a range of values that can be used to create globally-unique enum values. Most values will be negative numbers, but positive numbers are also reserved. The ability to create both positive and negative extension values is necessary to enable extending enumerations such as etext:VkResult that assign special meaning to negative and positive values. Therefore, 1000 positive and 1000 negative values are reserved for each extension. Extensions must not define enum values outside their reserved range without explicit permission from the owner of those values (e.g. from the author of another extension whose range is infringed on, or from the Khronos Registrar if the values do not belong to any extension's range). [NOTE] .Note ==== Typically, extensions use a unique offset for each enumeration constant they add, yielding 1000 distinct token values per extension. Since each enumeration object has its own namespace, if an extension needs to add many enumeration constant values, it can reuse offsets on a per-type basis. ==== The information needed to add new values to the XML are as follows: * The **extension name** (e.g. `VK_KHR_swapchain`) that is adding the new enumeration constant. * The existing enumeration **type** being extended (e.g. stext:VkStructureType). * The name of the new enumeration **token** being added (e.g. etext:VK_STRUCTURE_TYPE_SWAPCHAIN_CREATE_INFO_KHR). * The **offset**, which is an integer between 0 and 999 relative to the base being used for the extension. * The **direction** may be specified to indicate a negative value (`dir="-"`) when needed for negative etext:VkResult values indicating errors, like etext:VK_ERROR_SURFACE_LOST_KHR. The default direction is positive, if not specified. Implicit is the registered number of an extension, which is used to create a range of unused values offset against a global extension base value. Individual enumerant values are calculated as offsets in that range. Values are calculated as follows: * [eq]#_base_value_ = 1000000000# * [eq]#_range_size_ = 1000# * [eq]#enum_offset(_extension_number_, _offset_) = _base_value_ {plus} (_extension_number_ - 1) {times} _range_size_ + _offset_# * Positive values: [eq]#enum_offset(_extension_number_, _offset_})# * Negative values: [eq]#enum_offset(_extension_number_, _offset_})# The exact syntax for specifying extension enumerant values is defined in the `readme.pdf` specifying the format of `vk.xml`, and extension authors can also refer to existing extensions for examples. If an extension becomes part of core, the enumerant values should remain the same as they were in the original extension, in order to maintain binary compatibility with existing software. [[extensions-reserving-bitmask-values]] === Reserving Bitmask Values Enumerants which define bitmask values are a special case, since there are only a small number of unused bits available for extensions. For core Vulkan API and KHR extension bitmask types, reservations must be approved by a vote of the Vulkan Working Group. For EXT and vendor extension bitmask types, reservations must be approved by the listed contact of the extension. Bits are not reserved, and must not be used in a published implementation or specification until the reservation is merged into <> by the registry maintainer. == Required Extension Tokens In addition to any tokens specific to the functionality of an extension, all extensions must define two additional tokens. * `VK_EXTNAME_SPEC_VERSION` is an integer constant which is the revision of the extension named `VK_extname` (`EXTNAME` is all upper-case, while extname is the capitalization of the actual extension name) in `vulkan.h`. This value begins at 1 with the initial version of an extension specification, and is incremented when changes are made. Note that the revision of an extension defined in `vulkan.h` and the revision supported by the Vulkan implementation (the pname:specVersion field of the slink:VkExtensionProperties structure corresponding to the extension and returned by one of the <>) may differ. The revision value indicates a patch version of the extension specification, and differences in this version number maintain full compatibility, as defined in the link:html/vkspec.html#fundamentals-versionnum[API Version Numbers and Semantics] section of the <>. [NOTE] .Note ==== Any changes requiring the addition or removal of a type or command should be done by creating a new extension. The resulting extension should take care to include the appropriate dependency information on the original extension. ==== [NOTE] .Note ==== When the Debug Report extension (VK_EXT_debug_report) was recently updated to include the enum values of VK_DEBUG_REPORT_OBJECT_TYPE_DISPLAY_KHR_EXT and VK_DEBUG_REPORT_OBJECT_TYPE_DISPLAY_MODE_KHR_EXT, we violated this policy. That change was done prior to this revision policy clarification. From this point forward, we intend to follow this policy. ==== * `VK_EXTNAME_EXTENSION_NAME` is a string constant which is the name of the extension. For example, for the WSI extension `VK_KHR_surface`, at the time of writing the following definitions were in effect: [source,c] ---- #define VK_KHR_SURFACE_SPEC_VERSION 24 #define VK_KHR_SURFACE_EXTENSION_NAME "VK_KHR_surface" ---- == Extension Handles, Objects, Enums, and Typedefs Expanding on previous discussion, extensions can add values to existing enums; and can add their own commands, enums, typedefs, etc. This is done by adding to <>. All such additions will be included in the `vulkan.h` header supplied by Khronos. If the extension adds a new handle to Vulkan, a corresponding value must be added to ename:VkObjectType (as defined in the "`Debugging`" section of the <>) in order to allow components to identify and track objects of the new type. The new enumeration value must conform to the naming defined in the <> section. In this case, the type's etext:Vk prefix is replaced with the enum prefix etext:VK_OBJECT_TYPE_, and the rest of the handle name is converted as described in that section. [source,asciidoc] .Conversion of Handle to VkObjectType Examples: ---- VkSurfaceKHR -> VK_OBJECT_TYPE_SURFACE_KHR VkDescriptorUpdateTemplateKHR -> VK_OBJECT_TYPE_DESCRIPTOR_UPDATE_TEMPLATE_KHR ---- [NOTE] .Note ==== Application developers are encouraged to be careful when using `switch` statements with Vulkan API enums. This is because extensions can add new values to existing enums. The use of a `default:` statement, within a `switch`, may avoid future compilation issues. ==== [[extension-function_prototypes]] == Extension Function Prototypes Function pointer declarations and function prototypes for all core Vulkan API commands are included in the `vulkan.h` file. These come from the official XML specification of the Vulkan API hosted by Khronos. Function pointer declarations are also included in the `vulkan.h` file for all commands defined by registered extensions. Function prototypes for extensions may be included in `vulkan.h`. Extension commands that are part of the Vulkan ABI must be flagged in the XML. Function prototypes will be included in `vulkan.h` for all extension commands that are part of the Vulkan ABI. An extension can be considered platform specific, in which case its interfaces in `vulkan.h` are protected by #ifdefs. This is orthogonal to whether an extension command is considered to be part of the Vulkan ABI. The initial set of WSI extension commands (i.e. for `VK_KHR_surface`, `VK_KHR_swapchain`, and `VK_KHR_*_surface`) are considered to be part of the Vulkan ABI. Function prototypes for these WSI commands are included in the `vulkan.h` provided by Khronos, though the platform-specific portions of `vulkan.h` are protected by #ifdefs. [NOTE] .Note ==== Based on feedback from implementers, Khronos expects that the Android, Linux, and Windows Vulkan SDKs will include our `vulkan.h` and export the supported WSI functions for those platforms from their loader libraries. Other implementations can make different choices for their headers and loader libraries, but are encouraged to be consistent with these implementations. ==== == Accessing Extension Functions from Programs flink:vkGetInstanceProcAddr and flink:vkGetDeviceProcAddr can be used in order to obtain function pointer addresses for core and extension commands (per the description in the "`Command Function Pointers`" section of the <>). Different Vulkan API loaders can choose to statically export functions for some or all of the core Vulkan API commands, and can statically export functions for some or all extension commands. If a loader statically exports a function, an application can link against that function without needing to call one of the ftext:vkGet*ProcAddr commands. [NOTE] .Note ==== The Vulkan API loader for Android, Linux, and Windows exports functions for all core Vulkan API commands, and for a set of WSI extension commands that are applicable to those operating systems (see Vulkan loader documentation for the relevant platform/OS for details). The WSI functions are considered special, because they are required for many applications. ==== [[extensions-interactions]] == Extension Interactions Extensions modifying the behavior of existing commands should provide additional parameters by using the pname:pNext field of an existing structure, pointing to a new structure defined by the extension, as described in the "`Valid Usage`" section of the <>. Extension structures defined by multiple extensions affecting the same structure can be chained together in this fashion. Any structure which can be chained in this fashion must begin with the following two members: ["source","c++",title=""] ---- VkStructureType sType; const void* pNext; ---- It is in principle possible for extensions to provide additional parameters through alternate means, such as passing a handle parameter to a structure with a pname:sType defined by the extension, but this approach is discouraged and should not be used. When chaining multiple extensions to a structure, the implementation will process the chain starting with the base parameter and proceeding through each successive chained structure in turn. Extensions should be defined to accept any order of chaining, and must define their interactions with other extensions such that the results are deterministic. If an extension needs a specific ordering of its extension structure with respect to other extensions in a chain to provide deterministic results, it must define the required ordering and expected behavior as part of its specification. Validation of such extended structure chains is automatically generated from the registry, as described in the description of attr:structextends in link:registry.html[the registry document]. [[extensions-interactions-parent]] == Valid Usage and Extension pname:pNext Chains When there is a Valid Usage interaction between a parent structure and another structure appearing in the pname:pNext chain of the parent, that interaction must: be described in the explicit Valid Usage section of the parent structure, rather than the chained structure, and must: be protected by appropriate extension-specific `ifdef` constructs. For example, a constraint added to the slink:VkImageCreateInfo structure by the presence of two extensions which cannot interact is properly described as: [source,asciidoc] .Example Markup ---- // CORRECT: define interaction with children in parent VkImageCreateInfo // structure \ifdef::VK_NV_external_memory+VK_KHR_external_memory[] * If the pname:pNext chain contains an instance of slink:VkExternalMemoryImageCreateInfoNV, it must: not contain an instance of slink:VkExternalMemoryImageCreateInfoKHR. \endif::VK_NV_external_memory+VK_KHR_external_memory[] ---- However, a constraint added to slink:VkBufferCreateInfo by a structure in the `VK_NV_dedicated_allocation` extension must not be described as part of that structure's valid usage: [source,asciidoc] .Example Markup ---- // WRONG! Do not define interaction with parent in child // VkDedicatedAllocationBufferCreateInfoNV structure * If pname:dedicatedAllocation is ename:VK_TRUE, sname:VkBufferCreateInfo::pname:flags must: not include ename:VK_BUFFER_CREATE_SPARSE_BINDING_BIT, ename:VK_BUFFER_CREATE_SPARSE_RESIDENCY_BIT, or ename:VK_BUFFER_CREATE_SPARSE_ALIASED_BIT ---- Instead, define the constraint as part of the parent slink:VkBufferCreateInfo structure's valid usage: [source,asciidoc] .Example Markup ---- // REWRITTEN CORRECTLY: Define interaction with child in // parent VkBufferCreateInfo structure \ifdef::VK_NV_dedicated_allocation[] * If the pname:pNext chain contains an instance of slink:VkDedicatedAllocationBufferCreateInfoNV, and the pname:dedicatedAllocation member of the chained structure is ename:VK_TRUE, then pname:flags must: not include ename:VK_BUFFER_CREATE_SPARSE_BINDING_BIT, ename:VK_BUFFER_CREATE_SPARSE_RESIDENCY_BIT, or ename:VK_BUFFER_CREATE_SPARSE_ALIASED_BIT \endif::VK_NV_dedicated_allocation[] ----