Encode and decode HTML entities according to the standard

If you only need to escape text for embedding into HTML then installing is as simple as running:

cargo add htmlize

If you want to unescape entities back into raw text, see Unescaping entities into text below.

Escaping text into entities

The escape functions should cover most cases where you need to safely embed a string in HTML. Generally, if the text goes in an attribute, use escape_attribute(), otherwise use escape_text().

You should almost never need escape_all_quotes(), but it is included because sometimes it’s convenient to wrap attribute values in single quotes.

escape_text(string) -> string

Escape a string so that it can be embedded in the main text. This does not escape quotes at all.

Reference. See also escape_text_bytes().

escape_attribute(string) -> string

Escape a string so that it can be embedded in an attribute. Always use double quotes around attributes.

Reference. See also escape_attribute_bytes().

escape_all_quotes(string) -> string

Escape both single and double quotes in a string along with other standard characters. In general you should not need to use this.

Reference. See also escape_all_quotes_bytes().

Unescaping entities into text

This requires the unescape or unescape_fast feature. (unescape builds much faster, so unless you really need the very fastest unescape, use it.) To configure it:

cargo add htmlize --features unescape

unescape(string) -> string

This follows the official WHATWG algorithm for expanding entities in general.

Strictly speaking, this does not correctly handle text from the value of attributes. It’s probably fine for most uses, but if you know that the input string came from the value of an attribute, use unescape_attribute() instead. See the unescape_in() reference documentation for more information.

Reference.

unescape_attribute(string) -> string

This follows the official WHATWG algorithm for expanding entities found in the value of an attribute.

The only difference is in how this handles named entities without a trailing semicolon. See the unescape_in() reference documentation for more information.

Reference.

unescape_in(string, Htmlize::Context) -> string

This follows the official WHATWG algorithm for expanding entities based on the context where they are found. See the reference documentation for more information.

Reference.

unescape_bytes_in([u8], Htmlize::Context) -> [u8]

This is the same as unescape_in(), except that it works on bytes rather than strings. (Note that both functions actually take and return Cows.)

Reference.

Features

The escape functions are all available with no features enabled.

• unescape_fast: provide fast version of unescape(). This does not enable the entities feature automatically.

  This takes perhaps 30 seconds longer to build than unescape, but the performance is significantly better in the worst cases. That said, the performance of of the unescape version is already pretty good, so I don’t recommend enabling this unless you really need it.

• unescape: provide normal version of unescape(). This will automatically enable the entities feature.

• entities: build ENTITIES map. Enabling this will add a dependency on phf and may slow builds by a few seconds.

All other features are internal and should not be used when specifying a dependency. See the reference documentation.

Benchmarks

This has two suites of benchmarks. One is a typical multi-run benchmark using criterion. These can be run with cargo bench or cargo criterion if you have it installed.

To run benchmarks on the unescape functions, enable features bench and unescape or unescape_fast (or both).

Note: The internal bench feature is required to expose internal functions like unescape_fast() and unescape_slow() to the benchmarks. You must not enable this feature when specifying a dependency, since its behavior is not guaranteed to stay the same from point release to point release.

iai benchmarks

The other suite of benchmarks uses iai to count instructions, cache accesses, and to estimate cycles. It requires the internal iai feature to be enabled, and only really works well on Linux.

To run iai benchmarks locally:

cargo bench --features iai iai

You may want to use --all-features or --features iai,bench,unescape or --features iai,bench,unescape_fast to enable benchmarks of the unescape() functions.

To run in a Docker container, use the docker.sh script. It will build an image if necessary, then use that image for all future runs:

./docker.sh cargo bench --features iai iai

You can also start it in interactive mode and run the benchmark multiple times:

❯ ./docker.sh
root@d0a0db46770d:/work# cargo bench --features iai iai
   Compiling htmlize [...]

Development status

This is stable. I have no features planned for the future, though I’m open to suggestions.

License

This project dual-licensed under the Apache 2 and MIT licenses. You may choose to use either.

• Apache License, Version 2.0
• MIT license

The entities.json file is copyright WHATWG, and is copied from https://html.spec.whatwg.org/entities.json. It is licensed under the BSD 3-Clause License.

Contributions

Unless you explicitly state otherwise, any contribution you submit as defined in the Apache 2.0 license shall be dual licensed as above, without any additional terms or conditions.