hub75-framebuffer

DMA-friendly framebuffer implementations for driving HUB75 RGB LED matrix panels with Rust. The crate focuses on performance, correct timing, and ergonomic drawing by integrating tightly with the embedded-graphics ecosystem.

How HUB75 LED panels work (very short recap)

A HUB75 panel behaves like a long daisy-chained shift-register:

1. Color data for one pair of rows is shifted in serially on every cycle of CLK.
2. After the last pixel of the row pair has been clocked, the controller blanks the LEDs (OE HIGH), sets the address lines A–E, and produces a short pulse on LAT to latch the freshly-shifted data into the LED drivers.
3. OE goes LOW again and the row pair lights up while the next one is already being shifted.

Color depth is achieved with Binary/Bit-Angle Code Modulation (BCM): lower bit-planes are shown for shorter times, higher ones for longer, yielding 2^n intensity levels per channel while keeping peak currents low.

If you want a deeper explanation, have a look inside src/lib.rs — the crate documentation contains an extensive primer.

Two framebuffer flavors

Multiple Panels

• Use tiling::TiledFrameBuffer to drive several HUB75 panels as one large display.
• Combine it with a pixel-remapping policy like ChainTopRightDown and any of the framebuffers above (plain or latched).
• The wrapper exposes a single embedded-graphics canvas, so a 3 × 3 stack of 64 × 32 panels simply looks like a 192 × 96 screen while all coordinate translation happens transparently.

The latch circuit

The latched implementation assumes a small external circuit that holds the row address while gating the pixel clock. A typical solution uses a 74xx373 latch along with a few NAND gates:

The latch IC stores the address bits whilst one NAND gate blocks the CLK signal during the latch interval. The remaining spare gate can be employed to combine a global PWM signal with OE for fine-grained brightness control as shown.

Getting started

Add the dependency to your Cargo.toml:

[dependencies]
hub75-framebuffer = "0.4.2"

Choose your parameters

use hub75_framebuffer::{compute_frame_count, compute_rows};
use hub75_framebuffer::latched::DmaFrameBuffer; 
// or ::plain::DmaFrameBuffer

const ROWS:       usize = 32;              // panel height
const COLS:       usize = 64;              // panel width
const BITS:       u8    = 3;               // colour depth ⇒ 7 BCM frames
const NROWS:      usize = compute_rows(ROWS);          // 16
const FRAME_COUNT:usize = compute_frame_count(BITS);   // (1<<BITS)-1 = 7

// Create a framebuffer (already initialized/cleared)
let mut framebuffer = DmaFrameBuffer::<ROWS, COLS, NROWS, BITS, FRAME_COUNT>
    ::new();

You can now draw using any embedded-graphics primitive:

use embedded_graphics::prelude::*;
use embedded_graphics::primitives::{Circle, Rectangle, PrimitiveStyle};
use hub75_framebuffer::Color;

Rectangle::new(Point::new(0, 0), Size::new(COLS as u32, ROWS as u32))
    .into_styled(PrimitiveStyle::with_fill(Color::BLACK))
    .draw(&mut framebuffer)
    .unwrap();

Circle::new(Point::new(20, 10), 8)
    .into_styled(PrimitiveStyle::with_fill(Color::GREEN))
    .draw(&mut framebuffer)
    .unwrap();

Finally hand the raw DMA buffer off to your MCU's parallel peripheral.

Crate features

esp-hal-dma (required when using esp-hal)

Required when using the esp-hal crate for ESP32 development. This feature switches the ReadBuffer trait implementation from embedded-dma to esp-hal::dma. If you're targeting ESP32 devices with esp-hal, you must enable this feature for DMA compatibility.

[dependencies]
hub75-framebuffer = { version = "0.4.2", features = ["esp-hal-dma"] }

esp32-ordering (required for original ESP32 only)

Required when targeting the original ESP32 chip (not ESP32-S3 or other variants). This feature adjusts byte ordering to accommodate the quirky requirements of the ESP32's I²S peripheral in 8-bit and 16-bit modes. Other ESP32 variants (S2, S3, C3, etc.) do not need this feature.

[dependencies]
hub75-framebuffer = { version = "0.4.2", features = ["esp32-ordering"] }

skip-black-pixels

Skip drawing black pixels for performance boost in UI applications. When enabled, calls to set_pixel() with Color::BLACK return early without writing to the framebuffer, assuming the framebuffer was already cleared.

defmt

Implement the defmt::Format trait so framebuffer types can be logged with the defmt ecosystem.

doc-images

Embed documentation images when building docs on docs.rs. Not needed for normal usage.

Enable features in your Cargo.toml:

[dependencies]
hub75-framebuffer = { version = "0.4.2", 
                      features = ["esp-hal-dma", "esp32-ordering"] }

Running tests

cargo test

All logic including bitfields, address mapping, brightness modulation and the embedded-graphics integration is covered by a comprehensive test-suite (≈ 300 tests).

License

Licensed under either of

• Apache License, Version 2.0, (LICENSE-APACHE or http://www.apache.org/licenses/LICENSE-2.0)
• MIT license (LICENSE-MIT or http://opensource.org/licenses/MIT)

at your option.