sh1122-rppal

Crates.iosh1122-rppal
lib.rssh1122-rppal
version0.1.0
sourcesrc
created_at2021-12-02 16:52:29.852116
updated_at2021-12-02 16:52:29.852116
descriptionA user mode driver for SH1122 (Raspberry PI interface)
homepagehttps://github.com/cnwzhjs/sh1122
repositoryhttps://github.com/cnwzhjs/sh1122
max_upload_size
id491321
size2,610
(cnwzhjs)

documentation

https://docs.rs/sh1122-rppal/

README

SH1122 Driver

A user mode driver for SH1122 written in Rust.

demo

SH1122

SH1122 is a 256x64 16 grayscale OLED/PLED driver with controller.

It is very common to be used in a OLED display module with I2C, SPI, or 8-bit 6800-series or 8080-series interface.

What's included in this repository

  1. sh1122 is an abstract device driver for SH1122;
  2. sh1122-rppal uses rppal to drive a SH1122 display with Raspberry PI (note: I2C is the only supported interface yet);
  3. sh1122-clock is a sample binary using above two crates to display a clock on a SH1122 OLED display.

Prepare your Raspberry PI

The code is only tested on a Raspberry PI 4B board, but it should work on other models as well.
The only exception would be the first generation of Raspberry PI, which uses I2C0 instead of I2C1.
  1. Enable I2C and set baudrate to 400k

For modern Raspberry PI firmwares, you should change the /boot/firmware/usercfg.txt by adding dtparam to enable I2C and make sure it works at fast mode:

dtparam=i2c_arm=on,i2c_arm_baudrate=400000

Reboot to make this effective.

  1. Connect the display to Raspberry PI

    Make sure the Raspberry PI's power is disconnected while connecting the board and the display.

The SH1122 display is powered by 3.3v. Just connect the display's VCC to PI's 3v3, and connect SDL, SCL, GND of the display to those pins with same name on PI.

  1. Install packages required by the demo

The demo app uses freetype-rs and Roboto font to render text. Some packages should be installed before building this example:

sudo apt install -y cmake fonts-roboto gcc

Run sample binary

git clone https://github.com/cnwzhjs/sh1122-rs.git
cd sh1122-rs
cargo run

Get started

To use sh1122 in your own apps, just add these crates as your dependency:

[dependencies]
sh1122 = "0.1"
sh1122-rppal = "0.1"
rppal = "0.13"

Use the driver in your code:

use rppal::i2c::I2c;
use sh1122::*;
use sh1122_rppal::*;

// create I2C bus device
let mut i2c = I2c::with_bus(1).unwrap();

// create SH1122 communication interface
let sh1122if = Sh1122I2cInterface::new(
    &mut i2c,
    0x3cu8      // the device address (check the manual of your display module)
).unwrap();

// create SH1122 device
let mut sh1122 = Sh1122Device::with_interface(
    sh1122if,
    256,    // width
    64      // height
);

// initialize display
sh1122.init_display().unwrap();

// fill pixels
for y in 0..sh1122.get_height() {
    for x in 0..sh1122.get_width() {
        sh1122.set_pixel(x, y, x as u8);
    }
}

// transfer framebuffer to display
sh1122.flush().unwrap();

Contributing

:balloon: Thanks for your help improving the project! We are so happy to have you!

License

Licensed under MIT license.

Commit count: 0

cargo fmt